Tom King Posted September 25, 2017 Report Posted September 25, 2017 I've taken the job of putting a standing seam roof on a house on the lake, a few hundred yards from our house. I don't normally look for roofing jobs, but get 1-1/2 times my regular fee for roofing, if anyone absolutely wants me to do it. This is a particularly complicated roof, with two intersecting gambrels, two dormers in one gambrel, and a big low slope part with a slope change between the two intersecting gambrels. I get called behind most roofers around here to find, and fix problems, and this home owner has known me for years. He only wants me to do it, and doesn't mind paying to get the job done right.It also has ten skylights in it, on lower slopes than any commercial skylight manufacturer will guarantee against leakage, so I'm designing custom skylights that the "flashing" will be built into the standing seam panels. I'll post pictures once I get into it. I've found a fairly local manufacturer of metal roofing parts that I really like, and they will make custom trim parts for me to my specifications. Long story shortened some, I'm looking at getting one of these roller folders, so I can do some of the work up on the roof, without going up and down so many times to a brake. There are several manufacturers of similar things, but I'm probably getting one by this manufacturer. Probably the middle range one shown in this video: I somehow lost the video that I intended to post, but this one should do: Quote
wdwerker Posted September 25, 2017 Report Posted September 25, 2017 Video link didn't post. My great uncle invented the parallel jaw sheet metal pliers long before I was even born. My grandfather gave one of the prototype pairs that were made for the patent application to my brother. They had the patent number engraved on them after it was granted. Malco makes them now. 1 Quote
Tom King Posted September 25, 2017 Author Report Posted September 25, 2017 Check to see if it's working now. I lost the link when I first started the post, and had to go find it again. It shows on my computer. I have most of what Malco makes, but they don't make anything like these. Quote
wdwerker Posted September 25, 2017 Report Posted September 25, 2017 That does look like a very useful tool ! The tool is the 3" hand seamer. https://www.acwholesalers.com/Malco-HVAC-Tools/S2R-Redline-3-Hand-Seamer/35855.ac?gclid=Cj0KCQjwr53OBRCDARIsAL0vKrMBxmPnhJmNlpnVsApU-BK-exQcaIVN48jjcj82fTAaxR6hFqLba-IaAoyDEALw_wcB Quote
Tom King Posted September 25, 2017 Author Report Posted September 25, 2017 I use those a lot. They also come with offset handles, and now covered with vinyl, so as not to damage the steel coating. Also in 9" widths. I made some wider ones out of angle iron, and a couple of pairs of Vise Grips for folding edges around the drip edge. If I thought I'd ever do another gambrel roof, which I doubt seriously I ever will, I'd get four of these things. Since this is a one off roof, we're scaffolding up to a comfortable height to work on the roof edge, and making a comfortable to stand on ladder/steps to lay against the gambrel, that will also hold a plank. It's a shame these things cost almost a grand a piece. http://www.metalplusllc.com/product/big-boys/ Quote
Tom King Posted September 26, 2017 Author Report Posted September 26, 2017 Looking at others, I found that Malco does offer one model of, what I call a roller-folder, but it's limited to a small width, and I like features of the European models better. Quote
Tom King Posted September 28, 2017 Author Report Posted September 28, 2017 I ended up ordering the 14" model of the Wuku Uni Bender III, but it's not here yet. It seemed awfully expensive for all that there is to it, but I didn't have the time to make one. It cost almost as much as I paid for a used 20" masonry saw last week, and only weighs a couple of pounds. I'm hoping it's one of those things that I wish I had a long time ago-no more lugging a 200 lb. brake to a jobsite to fold chimney flashing with. We'll see. This video shows the tools I used to do the copper roof you can see on my website, back in 1991, although my finisher doesn't have the clips you have to operate. Mine you just have to hold down, which is plenty good enough, and saves the extra step. I've used those tools many times since then. Copper is a commodity, and I caught it at a low point then for 91 cents a pound- bought 7 thousand pound rolls. The last time I looked, it's 10 bucks a pound now. That roof should be good for another 600 years. 1 Quote
wdwerker Posted September 29, 2017 Report Posted September 29, 2017 So is the new job a copper roof too ? Quote
Tom King Posted September 29, 2017 Author Report Posted September 29, 2017 No, just regular colored (can't really call it painted) steel. It's a poorly designed, and poorly built house on one of the best lots on the lake. The owner has spent a lot of money trying to make something out of it over the fifteen years that he's owned it. It's not worthy of a copper roof, and the owner, at 80, now a widower, just wants the roof to stop leaking after putting several asphalt shingle roofs on it, and came begging me to put something on it that he would never have to worry about again. It's just a few hundred yards from our house. Quote
Tom King Posted October 4, 2017 Author Report Posted October 4, 2017 I used it for the first time today. It's amazing!! This roof has Prow gables, so we had to fold the long, angled, cut edges around the drip edge. No other way would have been as easy, as using this "roller folder", and it did a really pretty job.. Quote
Tom King Posted October 4, 2017 Author Report Posted October 4, 2017 It's a shame these things are so expensive. I'd really like to have one of these, but not bad enough to pay the price for it. http://www.steetz.com/buy-tools/sheet-metal-and-roofing-tools/sheet-metal-tools/sheet-metal-roll-bender/wuko-bender/wuko-disc-o-bender-twist-new/ Quote
Wood Basher Posted October 5, 2017 Report Posted October 5, 2017 How many of the old houses over there used lead for the roof or flashing? Does anyone ever renew the lead or does everyone change to more modern materials? When I was a student I worked part time for my grandfather who was a plumber in the old sense, meaning someone who worked with lead. He did lots of flashing work from tiny jobs up to a compete new roof on an abbey. When he started as an apprentice the first thing he had to do was make his own lead bashing tools out of wood and he used the same tools throughout his working life. Some of them are still around but they are awkward to use because he was left-handed and made his tools accordingly. I remember him announcing with great solemnity at the age of 80 that he had decided not to do any more roofing jobs. He was a real craftsman and I learned a lot from him, but I wish I had paid more attention - I could have learned so much more. Quote
Tom King Posted October 5, 2017 Author Report Posted October 5, 2017 The last time I tried to buy lead flashing, I couldn't even find a source. The last time I know of it being used was in 1997, Most of my flashing on old houses is with copper. I even have a page about it on my website. The only flashing I've found on houses 150 years old, and older, was lead, but it was always poorly done, from what I've seen. Quote
Tpt life Posted October 5, 2017 Report Posted October 5, 2017 Last time I worked for a local contractor they still required lead boots on vent pipes. No clue where they were sourced as the contractor provided them and micromanaged the installation...every time. Quote
Wood Basher Posted October 5, 2017 Report Posted October 5, 2017 No need for a source if you have sheet lead; just make it. Quote
Tom King Posted October 5, 2017 Author Report Posted October 5, 2017 I use these, as well as guttering from this company. The bellows is lead on the copper one, to allow for different roof slopes. It's a really heavy, nice piece, as you might expect from the price. http://classicgutters.com/product-category/roof-vent-pipe/ 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.