Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Board Game Shelves

Featured Replies

  • Popular Post

Finished product first, of course.

Our old board game storage didn't work out long-term so I needed to make something that would last a little longer and fit the space a bit better. At some point in the making of these shelves I considered making them smaller. I'm now glad I didn' t do that. Final measurements are 100"x16"x44". The base is constructed of 2x4s, with the rounded corners cut off, 2x2s for the x-braces, and edge-glued pine planks for the shelves. All wood was left to dry in my woodshop for almost a year to make sure it was as stable as possible. I think I won the 2x4 lottery on these because even after a year, these were some of the straightest 2x4s I've ever seen from any big box store. Pretty much counting on this never happening again.

vX2Gg3H.thumb.jpg.c29b3bc2906a7ee28afc15513a84373d.jpg

I wanted to use loose-tenon joinery on this... overkill for pine but this was also a chance to learn something new. Made a quick and fast jig for my router to cut mortises in the ends of the rails. Ended up a bit off-center but they worked out just fine.

uF9IQk1.thumb.jpg.f355407e81ddd005aecea85785dcfc5f.jpg

Cut my own loose tenons on the table saw and used the router table to round over the edges to match the mortises.

tzqhOF6.thumb.jpg.3393b24cc5fddc05592862e2bd31be80.jpg

Yes, I know these are not the prettyest mortises. I ended up squaring these off even though the tenons were rounded. The flat faces are the important part anyways. Was given a hollow chisel mortiser but it has a problem with the chuck so I drilled these mortises out with a forstner bit and squared them up with one of the hollow chisels and a mallet. Not the intended use for these, I know, but it worked. Cleaned up any irregularities with a regular chisel. Sorry I didn't get more pictures of this or of the final mortises.

IFHZrDQ.thumb.jpg.e750f324005109172345f4ba012a80db.jpg

Glue-up of outer frames. HF clamps are cheap and flex a bit but they do the job.

5BpPO36.thumb.jpg.a551a2d5380dabcffdda07a2c9a445db.jpg

Laying out the x-braces. Since the frame is mortise & tenoned, it's already sturdy as hell so these don't really provide anything structural and are more cosmetic. I half-lapped the point where they meet in the middle. I thought those angled half-laps were going to be a pain in the ass but they were quite simple.

gFcAE5p.thumb.jpg.cca174c17826b3664f91c057981190b4.jpg

Toenailed the braces in place with some glue on the ends. These fit like a glove. Ignore the misalignment on that top rail... wasn't happy about that one.

hrZSfPO.thumb.jpg.10436e34740f6b6b2de26c380535de7a.jpg

Initial assembly. The top was originally going to be 2x4s glued into a panel but I had this slab sitting in the garage with no clear plans and my wife thought it would look really good on the shelves. It had a slight twist to it but it was workable here.

S5uJZ9V.thumb.jpg.0591b4009fc9a1ce33c3d205e93ff6af.jpg

Brought the base inside to paint since it's getting a bit cold outside. I wanted the paint to dry a little quicker than it would have out in my shop. Primed it with some Zinsser BIN Shellac-Based Primer and then put two coats of enamel on it.

4m9bXTV.thumb.jpg.3569ecdeedc79f250bd2a0be15929094.jpg

Weu the kitten approves of the shelves.

tPDtMpE.thumb.jpg.36b945b74025d38e84282b3c5f1c2f39.jpg

Flattened the slab and got it all sanded up. I probably should have done something about the checking on the ends of this... butterfly keys or something. That will probably come back to bite me in the ass later. Will have to keep an eye on it.

numUK7m.thumb.jpg.35ace3a2325ec2101c6b090a5210a0a8.jpg

One coat of shellac to seal it and two coats of wipe-on poly later. I applied two more coats of poly after this before attaching it to the shelves.

9fTi1Ex.thumb.jpg.4bf650c861d6156d31b43464d0412f40.jpg

I drilled out oversized holes and used pan-head screws with washers to attach the top. Hopefully this allows enough leeway for movement. Got it moved into the game room and had the kids load it up with games and photo albums.

qOHfX3t.thumb.jpg.51718473013ea6bfc42ae09da6ecc735.jpg

 

  • Author

I'm correct in thinking not handling that checking is going to come back to bite me, aren't I...

I think that turned out really nice, Drow! You have wife/kid/cat approval, so you know you did well!

Can't answer the question about the checking, but do have a question for you: With the shelves already full, where are you going to put your copy of Gloomhaven when it arrives? :)

  • Author

Thanks! My wife presented me with an Ana White design and I refused to build it with pocket screws so I just used the basic design for inspiration and went with more solid joinery. Very happy with the sturdiness of the end product and it should last a long time. It was also the first time that the joinery went extremely smoothly. Very little adjustment needed in the tenons for a good fit and the angled half-laps required no adjustment at all, other than sneaking up on that perfect fit.

I've got an enormous list of board games on my wishlist and usually get several at Christmas so it looks like I may have to build more shelves... which means more time in the shop... darn ;)

Nice shelf and cool cat.    Did you do the half-lapped joints on the tablesaw?

  • Author
46 minutes ago, mat60 said:

Nice shelf and cool cat.    Did you do the half-lapped joints on the tablesaw?

Thanks! That's our new kitten we adopted. Luckily our existing cat has taken to her very well and we've not had any fighting amongst them. 

As for the half-laps, yeah, I marked them out with my t-bevel and then set my incra miter gauge and just sliced away. Did it on some scrap first and it came out very well so I just went for it.

I like it!!! It could have been constructed easier ( and cruder, if that’s a word), but your method and the new lessons learned, is what differentiates a carpenter from a woodworker!! Nice looking Drow! 

On 11/27/2017 at 12:00 PM, MisterDrow said:

Glue-up of outer frames. HF clamps are cheap and flex a bit but they do the job.

5BpPO36.thumb.jpg.a551a2d5380dabcffdda07a2c9a445db.jpg

 

 

I have the same clamps, ranging from 12 to 36" length. I actually like the fact that they are so lightweight. I have some much heavier duty Jorgensson bar clamps as well, which I also like, but one nice thing is the HF clamps themselves are lightweight, and don't unbalance a project or tip it over.  I'll often use a few HF clamps to get things held in place, and then start bringing in the heavier duty clamps to really lock it all down. 

19 hours ago, MisterDrow said:

Also... I thought Gloomhaven ended up being vaporware...

No. Oh, very much no. 21 pounds of box and goodness. Prepare to lose all your spare time....

Gloomhaven-components.jpg

  • Author
1 hour ago, ClassAct said:

No. Oh, very much no. 21 pounds of box and goodness. Prepare to lose all your spare time....

Gloomhaven-components.jpg

OMG! I can't find it for sale anywhere yet (except for someone selling it on Amazon for $240!!!). I take it you got in on the Kickstarter for it?

  • Author
15 hours ago, K Cooper said:

I like it!!! It could have been constructed easier ( and cruder, if that’s a word), but your method and the new lessons learned, is what differentiates a carpenter from a woodworker!! Nice looking Drow! 

Yeah, the traditional Ana White Pocket Hole construction would have been easier but I wouldn't have felt the pride I feel with this end result. Also, even in using traditional joinery, this project was completed in a weekend, which is faster than I've ever built a piece of furniture. I know it's a simple piece, design wise, but it felt good to just cruise through a project and have the whole thing come together so well with traditional joinery methods. I'm super excited to move on to the next project now!

15 hours ago, Isaac said:

I have the same clamps, ranging from 12 to 36" length. I actually like the fact that they are so lightweight. I have some much heavier duty Jorgensson bar clamps as well, which I also like, but one nice thing is the HF clamps themselves are lightweight, and don't unbalance a project or tip it over.  I'll often use a few HF clamps to get things held in place, and then start bringing in the heavier duty clamps to really lock it all down. 

Yeah, that's what I have... 12-36" lengths. For most things they have served me well, even with the large panel glue-ups for those desks I made. I also love the aluminum bar clamps from there and have had good luck with them. I have four Bessey 31" parallel clamps that are amazing, and I need to get my tail down to Woodcraft to snag some more while they are still on sale. If I had a larger discretionary budget I'd have way more of those on hand, that's for certain.

On 11/29/2017 at 10:38 AM, MisterDrow said:

OMG! I can't find it for sale anywhere yet (except for someone selling it on Amazon for $240!!!). I take it you got in on the Kickstarter for it?

Nope. Waiting for Wave 2 retail. I placed a preorder with my FLGS, and retail availability keeps moving out, probably due to slow boats from China (typical problem with game deliveries). I have Gloom of Kilforth, though, and I'll probably break it out the next week or so, time permitting. You can probably tell my game choices mean I'm a sucker for narrative in my games, not machine-building like Euros.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.