Nick2cd Posted February 28, 2011 Report Posted February 28, 2011 so i was playing with my sawstop tonight in preparation for a future project. i need to make a frame with 45's (just like a picture frame). i got out some scrap wood and my miter gauge (the stock one that came with the saw). i set the gauge to 45 and made 4 pieces of equal length that i referenced with a stop block that i taped to my fence. anyways, after putting together the 4 pieces, the last miter didn't line up perfectly. there was a gap along the entire miter that was wider at the outer most edge of the miter. i think im probably less than a degree off....how do i fix this? trial and error? this could take a lot of scrap wood. is there a better method that im not thinking of? Quote
PaulMarcel Posted February 28, 2011 Report Posted February 28, 2011 Get an accurate 45-degree try square. At least you could use one piece, set miter gauge (and shim with paper) until it fits the try square perfectly. Easier way is with trigonometry I slept through. Get a piece of MDF. Make sure one corner is an accurate 90. Put that one against the miter gauge to the left (away from blade) and cut your presumed 45. Measure the two square sides in millimeters and the hypotenuse in millimeters. Modify the angle until that's dead on. Won't take as many tries as you think. Quote
Beechwood Chip Posted February 28, 2011 Report Posted February 28, 2011 What P-M said regards getting the angle. But I don't assume that I can cut four perfectly sized pieces. I creep up on the fit for each piece, especially the last. I cut them long, and trim until they fit perfectly (or, close enough). Quote
wilburpan Posted February 28, 2011 Report Posted February 28, 2011 How do i get perfect 45's on my table saw? Take your table saw, put a shooting board for miters on it, and use a hand plane. 1 Quote
tim0625 Posted February 28, 2011 Report Posted February 28, 2011 I like your quote at the bottom WP. I have determined you are not a Neanderthal spy...maybe instead a Lie-Nielsen Missionary... and everyone said?..."Amen". The shooting board would allow you to sneak up on the length like BC said while keeping the angle true. We're still looking for comment from the camp of the Wixey-ites. "Sneak up on the length but not on the angle!!" Quote
Beechwood Chip Posted February 28, 2011 Report Posted February 28, 2011 Nick, when you ask, "How do I fix this?", do you mean, "How do I trim the existing pieces to make the gap go away?" Or, "How do I keep this from happening next time?" "How do I trim the existing pieces to make the gap go away?" You need to figure out if your pieces are a little long, or if the angle isn't 45, or both. To check the 45, put two pieces together and compare to a good 90 reference square. If you can see light between the piece and the square, then you don't have a good 45. Checking the length depends on whether you are framing something that's already cut to size, or make a frame that needs to be square and neat, but can be large or small by a millimeter or two. If you are framing a fixed size panel, then hold each piece up to the panel and make sure that the 45 cuts line up perfectly with the corners. mark each piece and each side of the panel. If the panel isn't perfectly square, you may need to adjust the 45 angles to make everything fit. The bad news is, if a piece is short you can only fix it with putty, wood filler, or caulk, or cut another. If you aren't fitting to a panel, then hold the opposite sides together and make sure that the short edges line up. trim the long piece. Again, mark the pieces that match. Don't try for four pieces the same length - try for two matched pairs. You can creep up on the fit using a table saw or a shooting board and hand plane. How do I keep this from happening next time? Start with scrap wood and make sure that your 45 cuts make a perfect 90. Then, cut the pieces long and creep up on the fit. Quote
Nick2cd Posted February 28, 2011 Author Report Posted February 28, 2011 Nick, when you ask, "How do I fix this?", do you mean, "How do I trim the existing pieces to make the gap go away?" Or, "How do I keep this from happening next time?" "How do I trim the existing pieces to make the gap go away?" You need to figure out if your pieces are a little long, or if the angle isn't 45, or both. To check the 45, put two pieces together and compare to a good 90 reference square. If you can see light between the piece and the square, then you don't have a good 45. Checking the length depends on whether you are framing something that's already cut to size, or make a frame that needs to be square and neat, but can be large or small by a millimeter or two. If you are framing a fixed size panel, then hold each piece up to the panel and make sure that the 45 cuts line up perfectly with the corners. mark each piece and each side of the panel. If the panel isn't perfectly square, you may need to adjust the 45 angles to make everything fit. The bad news is, if a piece is short you can only fix it with putty, wood filler, or caulk, or cut another. If you aren't fitting to a panel, then hold the opposite sides together and make sure that the short edges line up. trim the long piece. Again, mark the pieces that match. Don't try for four pieces the same length - try for two matched pairs. You can creep up on the fit using a table saw or a shooting board and hand plane. How do I keep this from happening next time? Start with scrap wood and make sure that your 45 cuts make a perfect 90. Then, cut the pieces long and creep up on the fit. i basically want to get my miter gauge set to cut a perfect 45 degree angle. i don't think my issue is length because i set up a stop block on my fence so i could get repeatable cut lengths. i think the angle is slightly off because the final piece was very close at the inside corner of the miter but the gap opened towards the outside corner of the miter. i think im either going to need a wixey 8" digital protractor or some scrap wood for trial and error until i get it perfectly dialed in. Quote
wilburpan Posted February 28, 2011 Report Posted February 28, 2011 I'd go the scrap wood route. Digital isn't always more accurate. The Wixeys are accurate to 0.1 degrees, so you can be off by 0.05º before the little counter ticks over. Multiply 0.05º by four corners on a frame, and that makes the last corner 89.8º instead of 90º. If your frame is 18" on each edge, that's a little less than a 1/32" gap, which is pretty small but easily noticable. Of course, if your frame is smaller, the error will be less, but the point remains. And that's assuming that your gauge is really accurate to 0.1º. If your reading is off by a full 0.1º, that translates into a gap of 1/8" at the last corner. Quote
Beechwood Chip Posted February 28, 2011 Report Posted February 28, 2011 I'm a big fan of relative dimensioning. I don't trust rulers, presets, gauges, stop-blocks, etc. If I want to things to be the same length I measure them against each other. If I want two angles to add up to 90 then I put them together and compare to a 90. I am not by any means a feeler gauge and thousandths of an inch type guy. I just want joints that fit without any visible gaps. Quote
Nick2cd Posted February 28, 2011 Author Report Posted February 28, 2011 Hey Beech, i think you have the same sawstop as me (contractor). do you cut your miters with the stock gauge, or do you have an aftermarket like an incra? Quote
tim0625 Posted February 28, 2011 Report Posted February 28, 2011 Hey Beech, i think you have the same sawstop as me (contractor). do you cut your miters with the stock gauge, or do you have an aftermarket like an incra? I like my incra...I don't usually have any problems with the angles. Still, the scrap wood route isn't bad. Quote
rmac Posted February 28, 2011 Report Posted February 28, 2011 And don't forget the idea of a miter sled. Once you get the fences on it perpendicular to each other, everything else just works. -- Russ Quote
Rick LoDico Posted February 28, 2011 Report Posted February 28, 2011 I use this miter set to get perfect angles on my miter gauges. Quote
BuilderBill Posted March 1, 2011 Report Posted March 1, 2011 i basically want to get my miter gauge set to cut a perfect 45 degree angle. i don't think my issue is length because i set up a stop block on my fence so i could get repeatable cut lengths. i think the angle is slightly off because the final piece was very close at the inside corner of the miter but the gap opened towards the outside corner of the miter. i think im either going to need a wixey 8" digital protractor or some scrap wood for trial and error until i get it perfectly dialed in. Try the technique on page 24 of this manual. Just note the results you get from the calculator are in degrees. The drag out your shooting board and the paper shims..... Bill Quote
Nick2cd Posted March 1, 2011 Author Report Posted March 1, 2011 I use this miter set to get perfect angles on my miter gauges. Rick, i guess this works pretty well for you? where did you get it? Quote
Rick LoDico Posted March 1, 2011 Report Posted March 1, 2011 Rick, i guess this works pretty well for you? where did you get it? I think I paid 30.00 for it from their website. Excellent customer service too. http://miterset.home.comcast.net/~miterset/index.html Quote
Nick2cd Posted March 2, 2011 Author Report Posted March 2, 2011 Update.....problem solved. I went the scrap wood route and finally got everything all dialed in correctly. it was initially off by less than half of a degree, but it was enough to make a difference. well, i don't know about u guys, but i sure do feel better now. Thanks for all the suggestions and help Quote
JimB1 Posted March 3, 2011 Report Posted March 3, 2011 Well, I see you got it dialed in but if your blade is parallel to your miter slots, this should do the trick too... http://www.rockler.com/product.cfm?page=18030&filter=45%20degre -Jim Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.