Popular Post Beechwood Chip Posted May 15, 2025 Popular Post Report Posted May 15, 2025 My general rule of thumb is that if you're going to touch the spinny/cutty part of a power tool, then you want more than one switch preventing it from turning on. So, if I'm changing a table saw blade, I turn off the paddle switch and the "computer switch" on my Sawstop. On a regular table saw I'd turn off the power switch and unplug it. On a hand held router, if I'm changing the router bit I'll turn off the router and unplug it. On my router table, this is less convenient. There is a switch on the front of the table, and the motor has a switch but it's inside the dust box. And the plug is behind the table against the wall. So, it's easiest to just turn off the main switch and go for it. Haven't lost a finger yet. The speed control is also on the motor, so I'm thinking of redesigning my table to make it easier to lift the motor up to get at the controls. I'm also thinking of wiring a second switch on the front of the table that I can switch off when changing bits. I'm guessing that no one else worries about this; they just turn off the router and change the bit. Especially since I've got one of those safety switches with a recessed "on" and paddle "off". Related question, does anyone have a clever way of accessing the speed control on the router motor in a table? My motor has speed control and soft start, so I can't use an external speed control. 3 Quote
fcschoenthal Posted May 15, 2025 Report Posted May 15, 2025 I have the same issue reaching in to change the speed control. I have seen several tables that the top is hinged at the back so you can lift the whole table up to access. Don't know if your table would be compatible with something like that, but it's another alternative anyway. 2 Quote
wtnhighlander Posted May 15, 2025 Report Posted May 15, 2025 I tend to follow the rules used at my job. If touching the "spinny / cutty" parts, an AIR GAP must be observed between the tool and its power source. At work, that means throwing a disconnect, locking the handle and either observing the knives in the open position, or verifying with a volt meter. At home, it means unplugging the tool, every time. I've seen switch contacts fail too often to trust. As for reaching the speed control, how averse are you to modifying the router in the table? You might hack in to the wiring, and relocate the control potentiometer to outside the cabinet. Or you might glue an extension to the control knob that allows for mechanical linkage for remote operation. 1 Quote
Beechwood Chip Posted May 15, 2025 Author Report Posted May 15, 2025 Thanks for the great suggestions! Since I'm going to build a new router table, I can run the cords to make it easier to unplug the table, and put hinges on the table top so it can lift up. Thanks! 1 Quote
Von Posted May 15, 2025 Report Posted May 15, 2025 Having at accidentally turned my table saw on once, I'm with you. On my router table, the switch runs to a plug inside the cabinet with the router, so I unplug the router there when changing the bit. I assume your router is hard-wired into the switch. If you are up for modifying the wiring, you could add a plug between the router and switch. 2 Quote
Mark J Posted May 15, 2025 Report Posted May 15, 2025 I am definitely with you in the two points of disconnect camp. Recessed switches are valuable, but not fool proof. Several years ago my friend sustained a serious (2 surgeries) hand injury while changing blades on his Jet TS with recessed switches. He had his cell phone in his front pocket, and while he was reaching far forward the corner of his cell phone "poked" the on button. I have a similar switch on my BS. I made a simple "safety pin" from a small dowel. The switch on my router table is on the side, which keeps the on button out of the way, puts the stop paddle out of knee reach, too. So when designing yours give some thought to switch placement. 2 Quote
Mark J Posted May 15, 2025 Report Posted May 15, 2025 And if you figure out how to do external speed control, I'd be interested. I think it is MCLS that has the router tables that lift up. The router is attached to the table, and I don't think they have a lift. Quote
Beechwood Chip Posted May 15, 2025 Author Report Posted May 15, 2025 On 5/15/2025 at 9:43 AM, Mark J said: I have a similar switch on my BS. I made a simple "safety pin" from a small dowel. The switch on my router table is on the side, which keeps the on button out of the way, puts the stop paddle out of knee reach, too. So when designing yours give some thought to switch placement. I forgot about the lockout feature on (some) switches. That may be an easy and convenient solution. Although an air gap would be safer. I want to maximize storage space in the cabinet, so I'm planning to put the switch in the center, in front of the dust box, so it won't be blocking any storage space. Thanks! 2 Quote
Popular Post gee-dub Posted May 15, 2025 Popular Post Report Posted May 15, 2025 On 5/14/2025 at 8:09 PM, wtnhighlander said: I tend to follow the rules used at my job. If touching the "spinny / cutty" parts, an AIR GAP must be observed between the tool and its power source. I am also an AIR GAP guy. My tablesaw and router table plug in to a wire way box placed specifically to make this easy. It would be easy to make a short properly gauged extension cord to bring your hidden router table connection up to a hook on the wall so you could reach it. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.