Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bought a new miter saw

Featured Replies

  • Popular Post

Rather than typing out a bunch, I'll just post one of the many videos.  I really have hated using an abrasive blade metal chop saw and it only cuts square anyway.  I'll be doing some metal fabrication over the next couple of years, so I went ahead and bought this.  The first job will be adding 51  24" long 1/2" x 3/4" rake teeth to my  12"  12-1/2 foot long I beam for my swimming area bottom cleaning rig.  The teeth will project 4" on one side and 8" on the other.  It's all just guess work, so I'll have a choice of rake tooth length to play with depending on which side goes down.   I have really been dreading cutting those 51 pieces with an abrasive blade, so here we go.

 

  • Author
  • Popular Post

Probably also having the edge of a cut right where I want it.  With the abrasive chop saw, the blade flexes and there is never a perfect cut.  My little bandsaw makes pretty cuts, but it takes forever to cut anything.   I get free delivery on metal if I wait until they're headed this way anyway, so I'm not sure when it will show up.  I've ordered a pallet fork for the excavator and am hoping that will get here before the metal does.  I have some old clamp on forks for the tractor bucket, but they're a PIA to use and cause me to worry about the bucket getting bent.

The 12' I beam weighs about 600 pounds and I'm past the point of being willing to risk getting hurt to do anything with heavy steel.  Steel is unforgiving to even just lightly bump into.

I have an old piece of junk dump trailer that I bought to build a dirt screen on.  That will require a bunch of angled cuts in angle iron which I could otherwise not easily or quickly do with the bandsaw.   

I want the screen on a trailer to save multiple steps of handling screened dirt.  I bought a sorry screen that a young guy was selling on FB marketplace just to learn with, and it was worthwhile.  It worked, but getting screened dirt out from under the screen took almost as much time as screening it.  If I screen it right into the trailer I can take it where I need to use it right after screening it, saving scooping it up out from under the screen, backing up, turning,  and pulling up to dump it into something to move it on.

  • Author
  • Popular Post

When I ordered it, I decided to wait until it got here to decide what kind, if any of a saw stand I wanted for it.   It's a lot heavier than a woodworking miter saw, so after looking at a bunch of them, I decided it's best to order the one made by the same company that makes this saw especially for it.

https://store.evolutionpowertools.com/products/mcsstand-mitering-chop-saw-stand?

I just looked and that saw is twice the weight of the Dewalt 12" non-slider DWS716. At 96 lbs, I think that stand with wheels and power assist lift is a good call!

  • Author
  • Popular Post

There is nothing about it that was made to be picked up by one person.  It's not only heavy, but very awkward to do anything with without a stand.  It's still on the floor in the shop, waiting for the stand to get here.  I'm probably going to have to recruit some help to get it positioned on the stand before I can bolt it in place.   The weight would be manageable, but I don't want to put fingers at risk of getting pinched.  It's bigger than a wood miter saw too.  Everything about it is bigger.

  • Author
  • Popular Post

There was more than "some" assembly required, but it's all together and I'm really impressed with it.  It was definitely the right call to get the stand made for it.  It was a one person job because the saw was in two main pieces to start with.

Only one small complaint that the pieces that slide over the ends of the clamps don't have anywhere on the rig to be stored.  I'll come up with something for that.

The stand goes up and down easily.  That's a good thing because there is not a very good way to roll it around in the up position.  

Every setup will take more time than setting up a cut on a woodworking miter saw.  Even the carriage for the saw head has to be positioned correctly for the different types of cuts and the clamping mechanisms are fairly complicated even if straight forward.  There is not supposed to be any hand holding of a piece of metal to be cut.

image.thumb.jpeg.3bced338ebe68b84debce7496a5edf40.jpeg

image.thumb.jpeg.b02f9d90d3a83fec674ac251d6fdd73f.jpeg

image.thumb.jpeg.8429a2563b9e51757aad120f879b3cb0.jpeg

image.thumb.jpeg.74f5399eefd81288198e2ec446e643eb.jpeg

I've heard that you need to be careful not to overtighten the clamps on that saw because they can bend the fence. Maybe it's been upgraded since I saw that comment, but something to watch out for just in case it hasn't.

  • Author

Thanks.  I think it would be pretty hard to do with the handles they have on the clamps.  Maybe they changed those.  Even when I was little, I always took very good care of my toys.   The fence is pretty massive too.   I will remember not to clamp against the unsupported part of the fence over the moving part of the table thanks to your post.

Does the saw have any provision to manage the sparks and dust?

  • Author
  • Popular Post

I'll post how it works once I use it.  I've ordered a couple of heavier roller stands than the ones I've used for woodworking, and the steel will show up when it does.  I'm only going to use it outside.  I don't grind metal in that shop either.

  • Author
  • Popular Post

The heavy duty roller stands came today.  I had looked online to see what was available and decided the Vevor ones looked like what I wanted and for a good price, but shipping would be weeks out from China.  Home Depot had some that looked identical but were sold under another name for just a couple of dollars more, so I ordered those.  These came in Vevor branded boxes, so they are the same thing.  I've been impressed with Home Depot's free, quick delivery lately and have bought stuff from them that I otherwise wouldn't have because of it.

They're supposed to be able to hold 2,500 pounds.  I'm not sure about that but they are much more substantial than the fold up ones I've used for so long for woodworking.  Having three legs will make them easier to wedge level.  They weigh 29 pounds each, but have a handle and are easy to move around.  

There is a quick adjustment and the roller is on about an inch and a half Acme screw for fine adjustment.

I wish my old ones for woodworking were back where they came from but if someone comes along who wants them, I'll give them away.

While I'm waiting for the metal to get here, Fall weather is finally here, so I'll go back to work on the barn apartment tomorrow.  I quit working in really hot weather forever.

image.thumb.jpeg.a9aeeef33812cf1e3adafff11b2a1ed9.jpeg

  • Popular Post
36 minutes ago, Tom King said:

I've been impressed with Home Depot's free, quick delivery lately and have bought stuff from them that I otherwise wouldn't have because of it.

+1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.