COMO Posted December 11, 2011 Report Posted December 11, 2011 I am relatively new to woodworking but started with the typical construction tools. I have bought most my tools used in order to save money. I recently purchased a Planer and a bench top Jointer that have so far proved to be very valuable. Currently I have a tablesaw, and router to go along with these tools. I was wondering what would be the next tool I should save for? It may be a while before the money is saved but I like to do as much research as possible. Currentyly I am doing small projects like, wine boxes, cutting boards, and picture frames, but would like to start my first piece of furniture after the holidays. Some of my first tool purchases were more of impulse buys so I would like to get the opinoins of more expereinced people as to what are important tools to have? Thanks Quote
mds2 Posted December 11, 2011 Report Posted December 11, 2011 Band saw is pretty handy. Also a drill press. Quote
areynoldsre Posted December 11, 2011 Report Posted December 11, 2011 Sounds like you've got a good setup going. Do you have dust collection set up? After that I'd look into (in this order) band saw, router table, drill press, and mortiser. and I bet you need more clamps... Quote
Beechwood Chip Posted December 11, 2011 Report Posted December 11, 2011 Here's the best answer I've seen to, "What tool should I buy next?" Quote
robjeffking Posted December 12, 2011 Report Posted December 12, 2011 I would buy or make a router table and you will need some sort of plan in place for joinery like finger joints, dovetails or pocket screws all these options should only set you back around 100 bucks Quote
COMO Posted December 12, 2011 Author Report Posted December 12, 2011 Thanks for the replies. Starting a project and then filling the need for a tools as needed was kind of my plan. Makes it easier to justify to the Mrs. I am finding there are never enough clamps in my shop no matter how small the project. Thanks again for the help. Quote
knotscott Posted December 12, 2011 Report Posted December 12, 2011 A router table is an excellent addition, as is a planer and jointer if you use much lumber. Quote
davestanton Posted December 15, 2011 Report Posted December 15, 2011 This question can open a can of worms if you aren't careful. Dust collection is a very good starting point, shop vac or 4 inch DC. It depends on how hard you are going to go with this need to make things as to how much money you should part with. I have listened to Marc say that buying the best or the machine that you really want, not just the machine you can get by with is a smart way to go and will save you money in the long run. Considering this, I think maybe a good bandsaw as others have mentioned would be a good move. Also, if the space you have needs work, money spent there could be something at the top of your list. Speaking of lists, have you written one and prioritised everything on it? Quote
PaulMarcel Posted December 15, 2011 Report Posted December 15, 2011 I'd say most of the tools and jigs I regret buying were bought before I had a specific need. I've since tried to only buy tools when I have a specific project that calls for it. This isn't to say I don't impulse buy still, uhm, far from it http://www.woodtalkonline.com/uploads/emoticons/default_rolleyes.gif' alt=':rolleyes:'> Getting a tool is quick these days with online sources. You could easily start a project with the tools you have, find that you need a Quadron X4R Whacky Orbital Multi-Mode Sander midway through and you can have it on your doorstep (hidden behind the column cuz you were at work) by the time you really need it. You already have a router; a great shop project is a router table; pretty inexpensive, too, so if you hate it later, not a big loss (because, of course you won't throw it out, you'll use it as jig stock). If it wasn't that you posted this under Normite City, I'd recommend getting a decent set of high-quality chisels (1/8", 1/4", 3/8" and 1/2" will do 95% of what you want); this set has great value; this set is stunning. But since you posted this under Normite City, I can't recommend that or a great bang-for-your-buck 20tpi rip dovetail saw; I just can't. 1 Quote
Joraft Posted December 15, 2011 Report Posted December 15, 2011 I'd say most of the tools and jigs I regret buying were bought before I had a specific need. I've since tried to only buy tools when I have a specific project that calls for it. This isn't to say I don't impulse buy still, uhm, far from it Getting a tool is quick these days with online sources. You could easily start a project with the tools you have, find that you need a midway through and you can have it on your doorstep (hidden behind the column cuz you were at work) by the time you really need it. You already have a router; a ; pretty inexpensive, too, so if you hate it later, not a big loss (because, of course you won't throw it out, you'll use it as jig stock). If it wasn't that you posted this under Normite City, I'd recommend getting a decent set of high-quality chisels (1/8", 1/4", 3/8" and 1/2" will do 95% of what you want); ; . But since you posted this under Normite City, I can't recommend that or a ; I just can't. Paul-Marcel? Isn't that the name of the guy who holds the Guiness World Record for driving unsuspecting woodworkers into bankruptcy? Quote
COMO Posted December 19, 2011 Author Report Posted December 19, 2011 I am slowly increasing my stash of hand tools as well. I just joined the guild and hope to build the shaker table once we return from holiday travels. I was looking at the tool list and it looked like a drill press would be handy. I have pretty much decided a drill press and a band saw are my next purchases with this project probably in that order. In my garage I only have room for one to be standalone and the other to be a bench top. I was leaning toward a bench top drill press but not sure if I should go the other way. Any thoughts on which tool should be the stand alone? Thanks for all the input so far. COMO Quote
PaulMarcel Posted December 19, 2011 Report Posted December 19, 2011 Bandsaw. I had a benchtop drill press for a long time and it worked very well. You'll want a floor-standing bandsaw for its mass; sure you could bolt down a benchtop model, but the flywheels won't have the mass of a full size bandsaw, and that all carries over to a better cutting saw. Plus the footprint of a larger bandsaw isn't much more than a smaller one so this way you reserve the floor space for a larger bandsaw. Quote
rmac Posted December 19, 2011 Report Posted December 19, 2011 I agree with Paul-Marcel, for even more reasons than he mentioned. -- Russ Quote
COMO Posted December 29, 2011 Author Report Posted December 29, 2011 Do you all have brands/models you prefer. I have looked at a lot of the shop pictures and see a lot of Ryobi bench top drill presses. My budget is probably about 500-600 for both a bench top drill press and a floor model band saw. I have the option of buying a craftsman 12 inch band saw really cheap but because space is an issue I hate to bring something in that I wont be happy with. Thanks for all the help so far. I finished a couple of end grain cutting boards for gifts and have plans to start a piece of furniture when we get back from a trip back to see family. Thanks Quote
PaulMarcel Posted December 29, 2011 Report Posted December 29, 2011 The Ryobi benchtop drill press is what I had (well, still have, friend hasn't picked it up yet... 8 months later). Other than quill travel, everything was great on it; quill travel can't be very far on a benchtop. Pretty sure I've seen this Ryobi on CL many times. You might have to watch CL to get a bandsaw in that price range. Should be able to get a good 14" bandsaw in that range on CL. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.