Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

In the market for a track saw

Featured Replies

I am in the market for a track saw. Work with mostly sheet goods... so i believe a track saw would make it easier to break sheets down.

Couple questions on track saws:

do you use them for final dimensions? or just rough out parts?

what length of track is a good all around length? I was thinking having two, one for a 4' length and one for 8' length to cross cut or rip sheet goods.

The big question....

What track saw do you prefer, recommend, do not like, or do not recommend?

Best place to purchase?

If I were in the market the only one I'd buy is festool. The 4ft track it comes with is a little longer than 4ft you need room for the saw to enter and exit. Same goes for the long one used to rip full sheets. You can use them either way, either to rough or make final cuts. They are slow and tedious but get the job done eventually. If all your doing is roughing I'd say they are a waste of money. You can do that with any circular saw and clamp guide for alot less money. For ripping full sheets they reall are not needed at all if you have some space and a full sized table saw. They are great for crosscutting full sheets but thats really about the only thing I might use one for.

Don

To answer your questions:

  1. Both. I have the Festool track saws and I do both rought and final dimensioning. They are accurate enough to to the final deminsioning work with but if I am making multipuls I usally break down the sheet goods with the track saw and then do final trim on my table saw.
  2. I first got two of the 55" (FS 1400) and the kit to join them together. This worked very well and is easy to transport (I have the case as well). Later on I got the 106" track for the shop and it is nice to have but not a must.
  3. I got a Festool TS 75 first. My thinking was it can do everything a TS 55 can and more. It however is a beast and for sheetgoods it is overkill. Later I got the TS 55 and it became my go to track saw for almost everything. I still run into the occasion that I need the 75 but I recomend the TS 55. The only other one I have tried was the Dewalt and while it worked fine I do prefer the Festools they just seemed to work better for what I was doing. One thing to keeep in mind is that with Festool you are buying into a tool system that has many other parts. I use the rails with my routers and the vac with everything.

I bought my stuff from several places. Most came from http://www.bobmarinosbesttools.com but I also bought some from my local dealer in town.

-Gary

I use the Festool TS55 for breaking down all my sheet goods. At first I used it to rough the parts out and final dimensions on the table saw. But that was a waste of time as the TS can do final cuts - so now I make final cuts using the TS55 when I know the dimensions I want for a project.

If you have multiple cuts of the same dimension, the parallel guides from Festool are the ticket for that. It's a like rip-fence for the TS.

As Gary mentioned - the TS55 is the go to for most people due to the smaller size and weight - much easier to handle. Rarely do you need more cutting depth (of the TS75)

And as for rails - the one it comes with is good for crosscuts. Get the FS3000 for the long dimension - the little bit extra length (longer than 8') is good for the parallel guides if you ever get them.

I have the DeWalt with the 55" and 48" tracks. I join them together to cut in the 8' dimension and use individually for shorter cuts. The two tracks came with the saw and I haven't seen the need to spend the money to get the single piece long track. I'm not a pro so I don't use the rig on a daily basis. If I did, I'd probably get the long track to save the time of assembling the tracks.

Depending on the project, I have used the saw for both rough and finished cuts.

The biggest issue for me was to build a low cutting bench large enough to support the plywood so I don't have to get on my hands and knees to make a cut. I usually work with a stack of sheets and use spacers to support the top sheet that I'm cutting.

Just purchased two of the Festool 1400 tracks yesterday as they went on sale where I work. The joiners should arrive from Amazon by the weekend. Next purchase is the TS55 when it comes on sale. I considered the TS 75 but as I already own a Bosch 9 1/4" circular saw so I have that size and power covered. The TS55 should be comfortable to use due to its weight.

  • 2 weeks later...
  • Author

Bought the TS55... man that is a great saw! Speeds up breaking down sheet goods! as well as finish cutting!

It was nice to have for my current commission, I had the table saw setup for a 1/2" dado but needed to cut some panels... boom TS55 here I come!

Bought the TS55... man that is a great saw!

Couldn't agree with you more!! I used mine a few times today. It really is a time saver. I would recommend this to everyone.

Put me on the Festool TS55 bandwagon. I got it bundled with a Festool dust extractor and love that setup. It can be used to cut down sheet goods to final dimensions and the dust control is really good. I went back and forth between it and the Dewalt, and didn't feel like the price difference was enough to chose the Dewalt over the Festool. Really happy with my purchase.

  • Author

My next purchase is going to a dust extractor, and chop saw ( not sure if i will purchase the festool)

If you're going to look at the Festool extractor, you can get a price break when bundled with a track saw or the miter saw. I didn't go with the Festool miter saw, I went with the Bosch 12" instead.

I'm also a Festool junkie. So, I use the TS55 for sheets goods break down and then either my Unisaw or the MFT for final dimensions. I also use a CT26 Dust Extractor. When you buy into Festool, you're buying into a system.

  • Author

I'm also a Festool junkie. So, I use the TS55 for sheets goods break down and then either my Unisaw or the MFT for final dimensions. I also use a CT26 Dust Extractor. When you buy into Festool, you're buying into a system.

Excellent point

I'm also a Festool junkie. So, I use the TS55 for sheets goods break down and then either my Unisaw or the MFT for final dimensions. I also use a CT26 Dust Extractor. When you buy into Festool, you're buying into a system.

Or you are buying inot the crack they are putting in that green koolaid!! Just cant get enough....

My next purchase is going to a dust extractor, and chop saw ( not sure if i will purchase the festool)

We now stock both the Festool Kapex 120 and the Bosch glide saw where I work.

The Bosch has the advantage of a 12 inch blade and also an insane 60 degrees when swung to the right. Other than that it is a cumbersome saw that lacks acuracy and rigidity when cutting mitres.

The Kapex is just a dream machine that is by far superior engineered and when you have them sitting side by side as I do every day, the difference becomes more and more apparent.

When it comes time to replace my old clunker it will be with the Festool kapex 120, no question about it.

Dave - thanks for the quick thoughts on the two saws side by side. That is great info - love when someone gets the chance to really use comparable products and give a real world comparison. Thanks.

I went with the TS75 because I deal with thicker rough stock and sheet goods. A track saw has changed the way I work with sheet goods.

  • Author

I went with the TS75 because I deal with thicker rough stock and sheet goods. A track saw has changed the way I work with sheet goods.

I was debating but for a small hobby shop like mine i was dealing with stock that could be handled by the TS55. and it has changed the way I work with sheet goods as well!

The 55 is a lot lighter than the 75. If you normally use sheet goods or 4//4 to 6/4 stock then it's perfect! B)

Yeah - the TS55 is perfect - it's rare that I'd need that extra 3/4" depth - and the weight and size difference is much better going with the 55

Thanks for that comment, Dave

There has been a bit of "chatter" about "problems" when linking tracks. Good on ya!

I joined up two tracks (1400 and 1900) again tonight to rip some oak ply. After the cut, I took the offcut, flipped it over, and lined it up back against the cut edge. In the middle where the join was, it took an 0.008" feeler gauge to flush it up, meaning the real error was 0.004" over 96". I can live with that :lol:

After borrowing one for a couple of days i finally purchased the ts55 yesterday. love that saw.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.