Recommended Posts

Posted

Not sure if this is the best place, but we'll start here..

I'm gluing up some bowl blanks and then truing them up via my handy drum sander (a new Jet/powermax 16") and I'm running into an issue where the paper is getting gummed up something nasty. From what I can see, it SEEMS to be from a single component of my glueup, a piece of bacote about an inch wide.

Note that the block is roughly 8" on a side, glue is standard yellow PVA, and had been glued up about 24 hours previously. Most of the excess glue had been scraped/chiseled off beforehand (no big globs left), and I'm trying to take relatively light cuts (1/32" to 1/64"), using 80 grit paper. Also putting the workpiece through at an angle to more evenly use the paper...

Note 2, I'm still new to the whole drum sander operation thing, so If I'm missing something dumb, don't hesitate to point it out.

So, some questions:

1. In general, if I see buildup like that, will switching to a lower grit (36 in my case) help?

2. I have a crepe block for cleaning sanding belts, and it helps a bit, but won't get the stuff out that is really 'ground in'.. I've thought of using a wire brush.. Thoughts?

3. I was thinking of trying to add a 'stearate' to the drum before doing my pass, like rubbing it with a bar of soap. Am I crazy? (Ok, to be clear, yes, I'm crazy in general, but is this one item crazy..)

4. The paper I am using is the standard Jet paper that comes with the machine. Is there perhaps a better paper I can get? (from looking at it, the quality seems fine, but not all aspects of quality are immediately obvious to newbs like me..)

Regards from the frozen north..

Thanks to all...

Da Bear..

Posted

I have the same sander and love it, also use the same paper. One thought, I haven't worked with bacote before but I am pretty sure it is an oily wood. A lot of exotic woods release an oil that can cause glueing and finishing problems, that is why you have to wipe them down with acetone before glueing and shellac before some finishes. I would assume that this oil is what is causing the gummed paper. Are you handy with planes and scrapers?? Switching to a course grit I would think would help but you aren't going to get a good finish either and are still going to have to go to a higher grit before you can finish. I could be wrong but this is my guess.

Posted

Use a coarser grit, take a lighter cut, watch your speed. Clean the sand paper frequently with a crepe rubber stick. Sometimes very light cuts(1/16th of a handle turn) and medium speed feed rate works well. It seems once you have the surface flat that finer grits behave better with less burns.

When I drum sand hard, dense, or oily wood I watch the out-feed side side like a hawk. At the first sign of a burn turn off the motor and clean the sandpaper.

If a burn won't clean out of the paper we mark the bad area on the outside of the machine with a pencil and work around it until we need to sand something wide enough to require a paper change.

Posted

I have the same sander, if the crepe block doesn't work for getting burn marks off of the paper, I open the cover and use a peice of hard maple or ash (1/2 x 3/4) and work the area where it is gummed up with the end grain of the stock.. This will usually clean the belt unless the paper is damaged.

If you are getting burning, I would recommend a coarser grit paper and slower feed rate.

Posted

Usually gumming up and/or burning is caused from the grit being too fine for the feed rate and possibly taking too much for the hardness of the wood. I only ever go up to 100 grit and it's at a very shallow cut and very slow feed rate. I usually only use the 80 grit and take light passes at the fastest feed rate, then go to card scrapers. I have the Delta 18-36, which is an inferior machine to the 16/32 Performax.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined