Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Which Flexner book?

Featured Replies

So after the bed finishing fiasco my wife asked me if there was a book that I could get to get more info on finishing. So I told her 'well there is this class that i want to go to up in VA, but its $475'. So then I told her 'well I have Marc's book, so what else do i need?'. To which she replied 'obviously more since you messed that one up pretty good'.

Ouch.

So I went on Amazon looking to get one of Flexner's books. So which one? I read the reviews on several and there were a lot of comments that most of the info was rehash from other sources (books/columns). I'd like to have a pretty comprehensive source, but one that someone who is still a beginner can make good use of. The three i was looking at were:

Understanding Wood Finishing: How to Select and Apply the Right Finish (American Woodworker)

Flexner on Finishing: Finally - Answers to Your Wood Finishing Fears & Frustrations

Wood Finishing 101: The Step-by-Step Guide

I have the first Understanding Wood Finishing and it is great but the is no substitute to practicing on test boards. What finish schedule did you use on the bed and what went wrong?

Flexner's updated, Understanding Wood Finishing would be the place to start

Dresdner's Book is also highly recommended -- Dresdner is a bit dated as of now

Jewitt/Taunton Finishing is another -- but also a little dated

CN's DVDs are very good -- some of it is step-by-step, but some is a 'brain-dump' and will benefit the more experienced (and even lead the beginner down false paths). Even though much is geared for hand-applied, at [almost] every turn, spray gear is required to get the job done properly using the products/techniques presented. There is a too much emphasis on a particular family/brand of products to the point that you will obtain sub-standard (and maybe even poor results without spray gear). Overall, intermediates will get more useful information then beginners from the DVDs and the end result highlights the downside of product sponsorship...

Hendrick Varju's's finishing DVDs are geared for the beginner, are [very painfully] step-by-step [read as strictly formulaic] and oriented towards those without spray capability. However, with a little experience, you will quickly move beyond HV's DVDs so they may be an expensive way to get introductory information. On the upside, they are not brand-specific and presents products/techniques geared to the best result [without spray] irrespective of brand-sponsorship. I think HV would be better for the absolute beginner without spray gear who wants a step-by-step formula for a decent finish using the half dozen most popular woods in North America -- but it takes 12 hrs of video to get you there.

Food for thought..............

Each finish manufacture has guidelines how to use their products successfully. These guidelines are thoroughly tested and predictable. How you use one finish makers products may not be recommend with another. Hence why so many folks get discouraged with finishing.

My advice to any finisher is to pick a finish manufacture and learn how to finish with them and not be jumping around. Once you learn how to finish successfully, by all means, jump around. Keep in mind...not all finishes are made alike. Think of it in terms of Harbor Freight vs. Powermatic or Festool. The same holds true in the finishing world.

Don Clark, it appears from your thread you had spray issues with oil-based enamels. Charles Neil does have other videos geared towards spraying that may be worth a look?

Good Luck!

-Ace-

  • Author

Most of my problems on the bed came from lack of information and inadequate planning. Throw in the fact that I am a novice at HVLP and there you go. I didn't have a specific finishing method picked out when the project was started, only that it needed to be gloss black to match the room decor. I was leaning towards an enamel, but wasn't sure when I did my stock selection and so that had an effect when I tried to change finishing methods when the enamel didn't spray.

I haven't had a chance to play with the enamel that I have left from the first attempt to see if it was just technique or if it wasn't suitable to be sprayed using the equipment that I have.

Regardless, I need a reference that I can go to when I have a question. Videos are good, but not as easy to find specific information in. If I had my choice, I'd like to go to Charles' class with my equipment and learn to spray using what I have, but given the fact that I am retiring from the Navy at the end of March and don't have a job lined up at this point that just isn't an option.

==> only that it needed to be gloss black to match the room decor...

'only' and 'matching' don't belong in the same sentence when it comes to finishing...

... matching an existing finish is one of (if not the) hardest thing to do in finishing... maybe in all woodworking... unless you know the original formula/schedule, of course... it's not just the 'color', but the entire material/prep/finish schedule impacts the outcome.

if you are interested in spraying... Dresdner and Jewitt both have texts and DVDs on spraying a finish. Both are very good. But they assume you already know about finishes, coloring, etc -- these sources just focus on how to get that finish schedule onto the surface...

I'm sure CN's classes are good because you can get clarification that is unavailable in the DVDs... But there is that small $$ thing...

As stated above, the best advice is keep cut-offs from the project and finish those first -- that's the only way to know if a particular finish plan will come out the was you want...

I have Flexner's revised Understanding Wood Finishing for details. I recommend his Wood Finishing 101: The Step-by-Step Guide for people who just want the basics and aren't trying to match stains when refinishing/repairing. Jewett is also good and I've heard great things about Neil. I agree with Mike Suiter about using test boards from your scraps.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.