Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

A few slight issues to discuss on the G0495x

Featured Replies

http://www.youtube.com/watch?v=N44RYKTXhOs&feature=youtu.be

This is where I am at as of now with my inspection of my new jointer. The pulleys were a good 1/2" out of alignment when I checked them. I corrected this problem, and I checked all the set screws on both pulleys, every things tight. I went for a process of elimination by removing the belt, and running the machine for a few seconds. Nothing. So the problem squeal is coming from the cutterhead section, possibly a bearing? I dont hear anything suspicious when I rotate by hand when machine is unplugged. What could this noise be?

Here are the results for the cast iron surfaces with the straight edge straight across from end to end with feelers:

- infeed table: .004"

- outfeed table: .001" (extremely snug)

- fence: .001" (not as snug as outfeed table)

Another issue to raise:

When I set the fence to 90 degrees i checked with a machine square at 4 points. The end of the fence closest to the infeed read different than the other 3 points. I thought maybe my tables were a bit off parallel and i would address this later. I made homemade winding sticks out of some small angle iron. I made sure they were referencing eachother correctly by sitting them back to back, they were fluch across the top. I set them at both ends of the fence and it proved my earlier findings to be accurate. There is a slight twist in the fence. I will attach a picture, it will be hard to see but if you zoom in you will see the back right side of the angle iron sits higher than the left side.

post-3732-0-50320300-1358480608_thumb.jp

Let me know what you guys think, thanks!

Let me know what you guys think, thanks!

I think it's time to make a table top. That squeal you hear is your jointer is hungry for some wood.

  • Author

I absolutely love this machine! I just want to address the fence and squeal issue, it seems to go away temporarily then come right back. One of my fathers assumptions was that sometimes bearings can get damaged while being pressed, but at this stage of the inspection i am kind of stumped as to what the actual source of the noise is. I was also missing the 4 screws for the dust port attachment, but I'm not gonna even bother grizzly about that, Ill just pick them up next time in at the store, no biggie. It seems kind of silly to keep checking the mailbox everyday for 4 screws, but if i need a new cutter head bearing, i dont know if thats something that can just be found locally, or is it dun dun dun

Maybe it's lost in the video, but it sounds fine to me. It ain't gonna purr like a Ferrari...jointers are noisy. Maybe it's just the whine of a new belt. Those things will break in and stretch and need to be tightened.

I'd return the fence. If it's not right, it's wrong. They'll email you a return label. Just take it to UPS and they'll send you a new one. Took me three shots to get a flat bandsaw table, but they kept trying until it was right. And it was an "Extreme Series" model, made in Taiwan, just like your jointer. They're supposed to be made at higher standards...and that's what I'd expect. You shouldn't feel guilty or like you're bothering them in order to get a perfect machine...you paid perfect money, after all.

  • Author

Sorry my video and pictures are from my iphone, the noise is a squeal which shouldnt be there, you can hear it the best during the end when the machine is powering down. As for the fence, its hard to see in the pic but its there, i can see it clearly in the winding sticks and in then square, so i guess i should be concerned about it.

I'd break the machine in, and see if the noise changes.

It might be a bearing or belt, but it could also be the cutters moving through the air and/or compressing air against interior surfaces. If it's air related, it may change or disappear once a dust collector is pulling air through the machine.

Since you're under warranty, I wouldn't be all that worried.

  • Author

Good points barry, but the squeal noise will suddenly stop for a few seconds while running then come back so i feel confident in saying its not the cutters moving through the air but i will consider all things until i pin point it.

DId you check the belt tension... I assume you did but that could be the culprit..

I had to watch it a couple of times but I do hear it as the machine is slowing down. Honestly, it wouldn't bother me and that jointer is pretty quiet compared to my PM.

  • Author

Usually a noise means everything is not working in unison. I would prefer to find it and fix it so it doesnt cause a bigger problem down the road.

On a side note, i cant believe how flat the tables are, eapecially the outfeed, wow!!! Doesnt get better than that

I just dont hear it. If anything for lack of better words it sounds dry. Take the belt of and run the motor without a load. Spin the head by hand and see if the bearing feel rough. If you dont find anything there Id live with it. It does seem a little loud but that may just be me being used to a heavier machine. Make sure your belt is not to tight and has the right deflection, to tight will kill bearings quick.

Don

  • Author

Don, i took the belt off last night and ran it, just the beautiful hum of the motor, so the problem is up top. Im gonna have my dad take another look at the cutter head assembly tn after work and ill post a video hopefully if i can set up a better light

  • Author

I took another look, i removed the belt again, this time i gave the cutterhead some wiggle at the pulley and i heard a slight knock, so i removed the pulley and tried again. The slight knock is still there. The pillow blocks are not loose at all. Is there an issue with one or both of the bearings?

Geez Freddie, just mill some damn lumber, wouldya? :D

You can't edge glue boards that are 0.001" off over 6' :D

  • Author

Im actually excited because i get to use the jointer right away. I have to make another wood bar top for a bar that I renovated right on the water in lindenhurst. I spent 2 months there and then hurricane sandy came, that was a horrible day walking into the bar with chest waders on seeing all my tools floating around and all the woodwork buckling off the walls.

  • 4 weeks later...
  • Author

As for the issues with my jointer, grizzly agreed to replace the fence and cutter head bearings. I dropped both items off to the muncy location. I received the new fence last friday, and I had to call cs to inform them that the new fence was bent. They worked with me and said they will inspect another new fence before shipping, so the next one will hopefully be the last one. I received my cutter head assembly today complete with new bearings. I re-installed it into the machine, started it up, and it ran perfectly normal, no more squeal noise, thank goodness for that. Now we are getting somewhere, and I am happy things are moving along more smoothly.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.