Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finish for quilted maple

Featured Replies

I have some quilted maple that had just stunning chatoyance when it came off the planer, but it seems to be less noticeable after sanding. I'm hoping a it comes back. I'm looking for suggestions on finishing it to get the maximum effect. I have a number of small scrap pieces which I will use for testing different finishes. I used Marc's method from "popping the grain" and used some transtint dye in shellac; used dye just diluted with DNA; and also more typical finishes - straight Arm-r-seal, some BLO, and a oil/varnish blend I had left over from a previous project. I don't have any lacquer to try.

I am most interested in bring out the shimmering effect. Any other suggestions?

Also, any thoughts on applying some oil after the dye/tint coat, or would going straight to the varnish finish be more appropriate? Any thoughts or suggestions welcome!

You will loose some of the figure sanding unless you sand up to higher grits, then you will see it come back. Your never loose the figure sanding. Remember figure is end-grain. The planer sheared the wood fibers cleanly, hence seeing the figure. The sanding with coarser paper just roughens the end-grain making it harder to see.

 

I like to dye my figured wood with transtint and denatured alcohol. I have also, and like to use various blends of Watco danish oil mixed in a jar. I will dye or Watco the wood up to 3 times and sand back the wood between coats leaving the dye in the end-grain the flat-grain should have low to no color in it.

 

After the 3rd coat sand, clean the wood and apply a coat of General Finishes Seal-A-Cell (if i used an alcohol/water-based die) to get that dye to travel deep in the curl. Then stain or dye to your final color.

 

If I used Watco danish oil to color the curl in the wood, after the 3rd sand, clean the wood and carry on with stain or whatever you used to take it to your finial color.

 

-Ace- 

Highlighting the chatoyance is different than popping the grain. I believe transtints are the best for popping, but the best way to highlight chatoyance is using oil. My favorite is a polymerized tung oil. There is a really great explanation if chatoyance on one of the earlier FWW Shop Talk Live episodes.

==> the best way to highlight chatoyance is using oil. My favorite is a polymerized tung oil

+1

 

I use Sutherland Welles for that....

 

I top to match the protection needed.... little abuse = couple more coats of SW; some abuse = Arm-R-Seal;  lot's of abuse = cat lacquer.

  • Author

Thanks guys. From these replies and other reading on the interweb it looks like oil is the key to bringing out the shimmer. I only have BLO but I'll look into polymerized tung oil. I did notice some enhanced grain pattern from using some dye ("popping the grain") so I might still start with that and sand back to at least 320, and then hit it with oil.

Nothing wrong with flooding dye onto figured maple, wiping it back, then sanding back.  Repeat...

 

Charles Neil had a video on this.  

 

http://www.youtube.com/watch?v=IWCptCxNx4I 

 

Works for any of the figured maples...  Warning, this technique needs to be modified for other species...  It's not a one-stop-grain-popper...

 

 

==> sand back to at least 320, and then hit it with oil.

 

320 may be good for end grain, but that's pretty high for the flats...

==> the best way to highlight chatoyance is using oil. My favorite is a polymerized tung oil

+1

 

I use Sutherland Welles for that....

 

I top to match the protection needed.... little abuse = couple more coats of SW; some abuse = Arm-R-Seal;  lot's of abuse = cat lacquer.

I LOVE Sutherland Welles.  It's spendy, but very much worth it.

  • Author

On the application of the dye - if I apply some shellac with dye in it (as in the popping the grain video) and sand back, should I expect the oil to still be able to penetrate?

==> On the application of the dye - if I apply some shellac with dye in it (as in the popping the grain video) and sand back, should I expect the oil to still be able to penetrate?

 

Yea, but the solids in the shellac will act as a retarder so you have to be careful...  You need a light cut, say 0.5# Super Blonde and Alcohol-based Dye/NGR/TransTint/etc as a the  toner...  The advantage of Alcohol-based is that it penetrates deep and dries fast.  I would only spray alcohol-based dyes unless for popping figured maple, then have at it...

 

But to get back to 'popping the figure'... But I'm not sure toning the shellac is the best approach...  A better (IMHO) is to dye the surface, sand back, repeat as you go through the grits starting at about 100/120 and stopping at about 180... Then go with a sealer, oil, etc..

 

==> as in the popping the grain video

who's video?  The link I sent?  CN does occasionally tint his seal coats, but not (to my knowledge) for figured maple -- unless it's a panel, but that's another discussion altogether... 

I don't know if tinted shellac is the best option, but it does work pretty well.

 

Attached is a picture of a jewelry box, the finish is curly maple with a coat of (1:1:1, BLO, Amber Shellac, Denatured Alcohol), and then GF Topcoat.

 

post-7224-0-35670500-1361740286_thumb.pn

  • Author

hhh - I actually was referring to Marc's "Popping the grain" video.

Chris - beautiful jewelry box!

Thanks everyone - lots to think about. I'll continue with trying different methods on some scraps.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.