Recommended Posts

Posted

The two tools I just purchased:

Grizzly G0715P Hybrid Table Saw

Grizzly G0656P 8" Jointer

 

I roughly set them up together, just getting the big bulk pieces put into place and loosely put the screws in. After that was done, I tuned the table saw to get everything where I liked it. The fence was very accurate, the miter slots were perfect, and the cast iron wings are a smidgen bit off perfect. Nothing I can't fix later. I made my first cut with a piece of Oak that was laying around. The stock blade is all I have at my Fiance's parent's house, so that had to do. It was magical.

 

Second, I moved onto the jointer. This took quite a bit more time to get everything where I wanted it. The tables were co-planar as far as I could measure. I will have to get a longer straight edge to fully check the beds, but that will come. I cleaned off the cutter head as best I could, and it was time to finally turn it on. I knew there was still some grease residue on the blades so I closed the blade guard and let it spin off. Worked like a charm, as I just had to wipe the bottom of the blade guard after letting it purr for a few seconds. It came time to run a board over the blades.

 

I grabbed a 2x4 I had laying around as well, and proceeded to square it up. I started with an edge just to get a feel for the cutter head. After that, I moved to a face, then back to an edge. I grabbed my square and it was perfect. First piece of wood and I couldn't even see a speck of light. I went to the table saw and squared off the other edge. All I need is my grandfather's thickness planer.

 

For how much I paid for these tools, I am ecstatic to report I am extremely happy with them so far. My first project coming up will require both of them, and it will be a blast to make. I will post pictures when I get some better shots.

 

Now I have to finish cleaning out that shop :/

  • Like 1
Posted

Nah, no spiral cutterhead for me. Just the plain knives :)

 

I kept the G0715P 240v and the jointer is only 240v, and I did do the wiring myself. I read books and diagrams for days and studied the best way to layout the wiring. Did not spare money for cheap materials, and took my time. Easy to do.

 

Don't mind the mess in the pictures, as it is still a work in progress. I didn't plan to buy the tools for a little while longer, but I saw there was a 10% off coupon, and couldn't pass it up. Saved almost $200 on top of the already good prices :)

 

Here is the jointer:

jointer_zps543f3b81.jpg

 

Here is the saw:

saw_zpsa78058cb.jpg

Posted

Don't ya just love when a plan comes together?! I suspect the stock saw blade won't stay sharp very long, so you'll want to replace that soon. Congrats and enjoy!

I will probably replace it with something along the lines of what I bought at my parents house. I think it was the 40tooth Diablo combo blade. That thing was amazing ripping and crosscutting soft maple and oak. $28 well spent.
Posted

Like that jointer.

 

I've wired all my 220 stuff myself as well. At first I was a little concerned and actually had my very first install inspected.... yeah, I know. Since then I've done it all myself with no worries.


Just curious, where did you find the coupon?
 

  • Like 1
Posted

Like that jointer.

I've wired all my 220 stuff myself as well. At first I was a little concerned and actually had my very first install inspected.... yeah, I know. Since then I've done it all myself with no worries.

Just curious, where did you find the coupon?

When James bought his saw, he posted about the coupon.
Posted

I got home from work today and I decided it was a good opportunity to run a piece of hard maple across the jointer. I decreased the amount of cut to about 1/32 - 1/16 of an inch, and it gave a flawless finish. Can't wait to start the first project.

 

Going to be something like this: http://1.bp.blogspot.com/_tfGC7tOlrdk/SoB2wgHojwI/AAAAAAAAIYk/lvjyE4NfhaI/s400/potato-onion-bin-pine.jpg

 

For storing potatoes and onions. 

Posted

Update:

 

I had some extra time, so I ran to Home Depot and picked up the 40 tooth Diablo blade. I used this blade before and I loved it, so I thought that it was worth a try here.

 

Got it on, and first time I noticed was it sounded much more solid as I turned the saw on. I don't know how to explain that, but it just sounded better. Second, the amount of effort to push a piece through was probably cut by 1/4 or more. Lastly, the quality of the cut compared to the stock blade is day and night.

 

This blade is spectacular for $30.

Posted

Pretty new tools! Congrats! I wish i had a jointer but i'd probably bust the knives on my first shot with a nail or something... I have your same blade and its wonderful ( i think you posted a thread about a good deal on amazon earlier & i took it up). I have noticed a considerable amount of deflection on that blade when cutting 2" + dense hardwoods even when i guide it very slowly. Just a heads up. Im going to try a blade stiffener and invest in different blades for different tasks. The table saw and jointer are such great tools i am happy youve got them!

Posted

Pretty new tools! Congrats! I wish i had a jointer but i'd probably bust the knives on my first shot with a nail or something... I have your same blade and its wonderful ( i think you posted a thread about a good deal on amazon earlier & i took it up). I have noticed a considerable amount of deflection on that blade when cutting 2" + dense hardwoods even when i guide it very slowly. Just a heads up. Im going to try a blade stiffener and invest in different blades for different tasks. The table saw and jointer are such great tools i am happy youve got them!

I love the blade for the price. For $30, you really can't beat it.

I will eventually invest in a Forrest, but that is awhile from now. This blade does a fantastic job, in my opinion. And I always feed the stock slow, no matter what type of blade I have. Just something I've always done.

That jointer, I just can't put it in words how happy I am. I am not exaggerating, I would recommend this jointer to anyone at any time. Put an extra hour or two in tuning it, and you save about $1,000. For me, a semi-hobbyist, it is a steal.

I am going to pick up a Festool ETS 150/5 this week. Also, probably a kreg jig.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 43 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined