Recommended Posts

Posted

Does anybody know why the 3HP Sawstop is $430 more than the 1.75HP?  The guy in the store says they are the exact same saw with only the HP being the difference.

Posted

I assume you are comparing the 1.75/110v and 3HP cabinet saws?

 

Not a sawstop guy myself, but I looked at them a year ago...  The basic difference was what's 'standard' in the 3HP and 'optional' on the 1.75 -- I believe you get a longer fence,  dust-removal in the blade guard, etc on the 3HP, but these are optional on the 1.75...  I seem to remember that the actual fence system was different on the 3HP saw, but may be an option on the 1.75...  I also seem to remember that the guts looked beefier on the 3HP -- but I was also looking at the 5HP, so could be mixing/matching...

Posted

My guess is that they pay more for three hp motors than 1.75 and the electronics are beefed up a bit along with maybe even a larger mount for the heavier motor. Just looking at the specs they are the same as long as you get the same fence. More HP more money.

Posted

More HP= more money. Look at the motors over at grainger and that will tell you. The only other thing I can tell you is the dust collection guard is standard in the 3hp model. I am kicking myself for missing the recent promotion. I personally believe they are a top quality saw and until you play with one and compare it you simply wont be able to tell. Just spin the height adjustment knob. Wow!

Posted

Thanks to all.  I called tech support and it boils down to some beefed up electronics, larger motor, and a dust collecting blade guard.  Sure wish I could swing the extra $500.  I bought the 1.75 today and will report on the progress.

Posted

that's my memory -- i think the better fence was an option at the time.  From memory, the better fence was indeed much better and worth it...

Posted

You can buy both the 1.75 hp and 3 hp with either fence. It's $2300 vs $2730 with the basic fence or $2470 vs $2900 with the better fence.  So it's a $430 difference either way.  The 3 hp comes with the dust collecting blade guard which you would have to buy for $140 on the 1.75 hp, bringing the difference down to $290 to get them equipped the same.  An extra $300 on a $2500 saw is well worth it when you think about how long that saw is going to be in service.  Of course if you have to hire an electrician to get 220 that changes the situation.

Posted

You can buy both the 1.75 hp and 3 hp with either fence. It's $2300 vs $2730 with the basic fence or $2470 vs $2900 with the better fence.  So it's a $430 difference either way.  The 3 hp comes with the dust collecting blade guard which you would have to buy for $140 on the 1.75 hp, bringing the difference down to $290 to get them equipped the same.  An extra $300 on a $2500 saw is well worth it when you think about how long that saw is going to be in service.  Of course if you have to hire an electrician to get 220 that changes the situation.

Thats a big factor to think about especially when you would need to upgrade your main panel from 100 amp to 200 to accomidate the saw because all your circuits are full!

Posted

==> This is a case where I think spending $2470 is the better value....

 

+1 -- I seem to remember that the 'low end' fence looked pretty sketchy.

  • 2 weeks later...
Posted

So it's been a week or so and I thought I'd say a bit about my new SawStop. 

* I went with the 1.75 model and the 36" fence.  The basic saw has only a low end fence which, unfortunately, is pretty bad and the deflection, front to back is dramatic. The stock miter gauge is your typical "stock" miter gauge and I have replaced it with a V120 from Incra, (more on that in another post). 

* As everyone has said in numerous posts, the setup and instructions are amazing.  They left out a few items but the tech support is awesome and very willing to help. 

* It's important to attach the wings starting with the center of the three bolts and then move to the outer ones after getting the center of the wing even and tight.  Maybe if I had done set up on more than one saw previously, I would have known that but all's good now I just wish it had been mentioned.

* The other thing not in the destructions is that leveling the wings is dependent on the angle iron used to for the fence so don't worry about that until you mount the fence and auxiliary table. 

* I had to adjust the table just a tad to align it with the blade and the fence needed adjusted but overall, everything was good.

* Both of the blade inserts, the one that came with the saw and the dado insert, were warped right out of the box but after a call to tech support, they had two new ones overnighted and they were both dead on. 

Overall thoughts, it's a great saw and extremely well made, tech support is probably the best I've ever dealt with, assembly was easy, and it looks really nice.  Only complaints were the "stock" fence and miter gauge as it seems that for $3K they could include a higher grade components and the warped inserts but dodo occurs and they took care of the issue promptly. 

 

Bill

 

Posted

I would agree the stock fence looked like a joke. On this kind of a saw the beismeyer fence is the only way to go. I thought why do they even have that stock fence? Im sure its a marketing thing.

 

I actually talked to a SS factory rep on this very issue. He told me that the cheapo stock fence was done with the specific goal of reaching a certain price point. Their market research assured them they needed to hit x dollars and no more. They didn't want to sacrifice the quality of the components of the saw which are difficult to up-grade. So, the took the cost out of the fence to reach the specified price point.

 

That's what the factory rep told me. Seems logical to me, my company does the same thing. We offer product designed to serve specific markets. We offer product to serve specific customers. And we offer product designed to hit specific price points.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 54 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined