Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Filler?

Featured Replies

I am still working on my enormous counter top of walnut, and I am getting close to the finishing stage. Because the stock was so long, I had to make some choices about imperfections. Overall, I did very well with no knots, splits, or major imperfections in any area on the show face. I do, however have these two small spots to deal with.

I tried a commercial filler on some cutoffs, but I was not happy with the results. The filler also filled some of the surrounding open grain, and made an ugly repair.

Any suggestions on how to best repar this? I thought about filling with wax after the clear coats, but I don't want to miss an opportunity to fix it better, if possible.

post-6372-0-76652800-1374247917_thumb.jppost-6372-0-05508900-1374247895_thumb.jp

Are they too deep for a wet sand repair of straight finish? I will be using general salad bowl finish.

Hey Pug,

 

Wondering if you could drill it out with a countersink (3/8") and cut a plug that was matched to the color and grain?  There are kits that come with both the countersink and plug cutter so they are an exact match in size.  If it's done with a good match it's almost invisible.. 

 

Just a thought :-)

Thought, have you ever ironed those defects? Dollop on some water drops right in the defects and heat with an iron to swell the fibers and dry them. You could get anywhere from complete closure to a reduction by half. Heat quickly to avoid over penetration of the water. It can leave some marks that need to be sanded. Probably better to try on a scrap first since you have already glued up.

  • Author

Hey Pug,

 

Wondering if you could drill it out with a countersink (3/8") and cut a plug that was matched to the color and grain?  There are kits that come with both the countersink and plug cutter so they are an exact match in size.  If it's done with a good match it's almost invisible.. 

 

Just a thought :-)

I do have one of those kits, but the largest spot is just under 3/4 if I needed to drill out a hole. It would break my heart to drill out as hole in this countertop after so much work. Plus, it would be a freehand hole as well. Thanks for the suggestion!

post-6372-0-96246900-1374248325_thumb.jp

  • Author

Thought, have you ever ironed those defects? Dollop on some water drops right in the defects and heat with an iron to swell the fibers and dry them. You could get anywhere from complete closure to a reduction by half. Heat quickly to avoid over penetration of the water. It can leave some marks that need to be sanded. Probably better to try on a scrap first since you have already glued up.

I'll try this on some scrap, good suggestion. Makes me a bit nervous, though!

Tape around the dent and fill it with crazy glue. Then level it put with a razor blade and then sandpaper.

If you dont plan on staining. Put a piece of 80g paper on RO sander and misalign the holes (block them). Fill the hole with super glue. Drop the sander straight down and sand away. The sanding dust will fill the super glue with dust and level off the hole at the same time.

Thought, have you ever ironed those defects? Dollop on some water drops right in the defects and heat with an iron to swell the fibers and dry them. You could get anywhere from complete closure to a reduction by half. Heat quickly to avoid over penetration of the water. It can leave some marks that need to be sanded. Probably better to try on a scrap first since you have already glued up.

 

If you dont plan on staining. Put a piece of 80g paper on RO sander and misalign the holes (block them). Fill the hole with super glue. Drop the sander straight down and sand away. The sanding dust will fill the super glue with dust and level off the hole at the same time.

 

One of my guys showed me the iron trick, got us out of jail a time or two. Done the PB trick too, glue and sanding can also be a useful trick.

  • Author

If you dont plan on staining. Put a piece of 80g paper on RO sander and misalign the holes (block them). Fill the hole with super glue. Drop the sander straight down and sand away. The sanding dust will fill the super glue with dust and level off the hole at the same time.

Will this effect the surrounding grain as well?

Will this effect the surrounding grain as well?

Only if you make a mess of it. Tape around the dent.

I have had some luck cleaning up accidentally filed grain with the liberal use of a cabinet scraper and compressed air. Scrape down the area then blow the grain clean, inspect, repeat as needed. After wetting and ironing to raise the grain and shrink the defect tape it off and fill by whichever method gives you the best results. After it is completely dry and sanded smooth blow all the dust out of the grain.

I have used a dental pic and a magnifying headband to scratch the grain pattern and pores back into a filled repair which is hard to find after the finish is completed.

Will this effect the surrounding grain as well?

No and you don't need tape. It won't work with tape, just try it you will probably find yourself doing it once on almost every project.

  • Author

No and you don't need tape. It won't work with tape, just try it you will probably find yourself doing it once on almost every project.

I'm going to practise on some off cuts today, after I scribe the counter to the wall. Thanks for the suggestion.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.