Sk1pp3r Posted July 20, 2013 Report Posted July 20, 2013 So I just joined the forum and this is my first post and my second project. The first project was a router table to make these Our laundry room had basic shelves but they looked messy and I thought why not. I just discovered The Wood Whisperer and wish I had known about a lot of the techniques sooner. Sketchup played a major role in the design. I'm glad I did because I found and worked out a couple problems, (for example the angled doors hitting the ceiling so they all had to have the hinge on the left side.) Face frame in. Notice the ceiling isn't square at all. So it looks like crown molding or something is going to be used. I used my router table to make tongue and groove joints and followed a lot of the Sommerfeld method. I can't believe they actually lined up Cabinets from the back without panels in From the front For everyone else here this is nothing new, but for this new woodworker I couldn't believe my joints. I was so proud. Next up the doors. . . . Quote
Sk1pp3r Posted July 20, 2013 Author Report Posted July 20, 2013 I designed the doors to overlap a 1/4 inch but after purchasing hinges and finding out they are half inch overlap, I had to go back and measure each rail and stile. So the doors will overlap 1/4 on each side except for the hinge side which is 1/2 inch. Using my router table again I cut all the grooves and they came out pretty nice. I used my drill press and forstner bit to make the holes for the hinges in each door. Then dry fit everything and glued them up. I stained it using Minwax natural and finished with their Polyacrylic. Here they are drying after two coats. I thinned it down so I could wipe it on so I'll probably end up with around five coats on the front. Here is a closeup of one of the joints. Not bad pics for an iphone lol Very happy so far with the outcome and can't wait to put the doors on! Quote
Tpt life Posted July 21, 2013 Report Posted July 21, 2013 Very nice!! I am not sure I would have attempted something quite like this but having seen yours it seems brilliant! Quote
..Kev Posted July 21, 2013 Report Posted July 21, 2013 Nicely done! Funny how much your laundry room looks like mine Yes, this is a project on my list too! Please don't show my wife! Quote
TRBaker Posted July 21, 2013 Report Posted July 21, 2013 Outstanding job, jhill. I can't wait to see the finished project. Welcome to the forum, btw. Quote
Sk1pp3r Posted July 21, 2013 Author Report Posted July 21, 2013 Thanks guys! Now my wife has many other projects lined up. That's another nice thing I like about sketchup. I could explode my drawing and put the pieces on a 4x8 sheet of plywood to make a "cut list". That's why two of the back panels are horizontal instead of vertical. Because I only used one 4x8 sheet of 3/4 inch and one sheet of 1/4 inch plywood for the shell and doors. The face frame and rails and stiles are solid red oak. Quote
Sk1pp3r Posted July 21, 2013 Author Report Posted July 21, 2013 Here is the cabinet in place. Kind of scuffed the walls up since it was such a tight fit on the sides. As you can still see the ceiling needs to be dealt with. It looks like the top angle of the cabinet is too acute for the ceiling but it's just from the panorama view on my iphone. It is parallel on the right side and then slopes upward towards the left. Any idea's for the top? Should I scribe the top rail or just apply crown molding? Quote
Byrdie Posted July 22, 2013 Report Posted July 22, 2013 Very nice job and the joints are terrific! I read your other post about covering the gap. I think a nice piece of quarter round would be the simplest route to a nice outcome. Quote
Sk1pp3r Posted July 22, 2013 Author Report Posted July 22, 2013 Very nice job and the joints are terrific! I read your other post about covering the gap. I think a nice piece of quarter round would be the simplest route to a nice outcome. I think you are on to something here. I sourced all my lumber from a box store and haven't found a hardwood dealer in my area yet to make my own crown. Trouble is, I didn't see any red oak crown molding today at either big box store. It's either pine or primed wood. They did have oak quarter round though so I think I might be going this route. The other option I was thinking of was to take a thin piece of solid oak and mimic the top of the rail. That way it would seem to blend a bit more. Still need to adjust the doors but I was excited to post a pic. Quote
Freddie Posted July 22, 2013 Report Posted July 22, 2013 This is the willy wonka hallway, I didnt even realize from the other post. What a head trip man haha. Thats very cool though that you made cabinets to fit in that wackadoo space. Quote
aerofly0610 Posted August 6, 2013 Report Posted August 6, 2013 very impressive, looks so professional Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.