Kenny McCarty Posted August 2, 2013 Report Posted August 2, 2013 Every time I have a riving knife installed on my table saw I get horrible binding....I have adjusted the thing for hours on end with no luck....it is a Delta Unisaw 36-L552. Measured its thickness with calipers and it is .112" thick....I am using a .125" kerf blade. I have tuned up my saw about 1000 times and it is now mostly within .000000000001" tolerances Anyone have any idea why this is happening? Is it possible for wood to suddenly warp immediately after cutting? I turned the saw off mid cut and could see the wood actually pinching the riving knife.... I would like to use the knife since it is a "safety" feature but I am getting a ridiculous amount of binding with it on which seems more dangerous to me.... Quote
G S Haydon Posted August 2, 2013 Report Posted August 2, 2013 Hello Kenny Bravo on having a riving knife and please keeping using it. It is indeed possible for wood to pinch just after cutting. This can happen because the wood is case hardened of there is tension in the wood built up during the tree growing. Iroko is a really notorious timber for doing this. What species are you cutting? Quote
Kenny McCarty Posted August 2, 2013 Author Report Posted August 2, 2013 I was just using walnut....it's really driving me crazy.... Quote
Tpt life Posted August 2, 2013 Report Posted August 2, 2013 Do you have a dead on straight edge? Have you laid the straight edge along your blade to verify alignment with the riving knife while in multiple blade height positions? Have you tried to rip some excess stock with a handheld circular saw to gauge how much stress is in a board that the TS struggled with? Quote
Beechwood Chip Posted August 2, 2013 Report Posted August 2, 2013 I once cut through a knot using a low powered job-site saw (no riving knife). The wood pinched so hard that the blade stopped turning. In this case it was "reaction wood" - the wood had grown fighting gravity, the wind, or some other force, and had internal tension. When the wood was cut, the tension was released. Does this happen with all your stock, or just some pieces? Quote
rodger. Posted August 2, 2013 Report Posted August 2, 2013 I have also had this happen on my TS. Sometimes the wood just wants to close up after the cut, due to the reasons mentioned above. Quote
wtnhighlander Posted August 3, 2013 Report Posted August 3, 2013 Mr. Rogers himself (Shannon, that is), has mentioned in the past that while walnut is a beautiful wood, it is a horrible tree, very cantankerous to cut. Maybe wood reaction really is the problem... Quote
Kenny McCarty Posted August 3, 2013 Author Report Posted August 3, 2013 I think it was just this particular tree....I cut some other walnut from a different tree and it cut just fine....but every board from this one tree is a pain in the @$$ to cut...it all starts to bow almost immediately after i cut it...oh well Quote
G S Haydon Posted August 3, 2013 Report Posted August 3, 2013 I think it was just this particular tree....I cut some other walnut from a different tree and it cut just fine....but every board from this one tree is a pain in the @$$ to cut...it all starts to bow almost immediately after i cut it...oh well Great news Kenny. That riving knife was doing its job. Imagine the force of that pinching wood on a blade, KICKBACK! 1 Quote
CessnaPilotBarry Posted August 3, 2013 Report Posted August 3, 2013 Great news Kenny. That riving knife was doing its job. Imagine the force of that pinching wood on a blade, KICKBACK! Exactly! The riving knife probably exchanged a major pain in the face or body for a very minor pain in the ass... Clean it up nice and thank it! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.