Tony Wilkins Posted October 6, 2013 Report Posted October 6, 2013 Got it earlier this week and I've been having a blast with it. Got the fence with it and it's been on since I got it. I've been working on the edges of the 8/4 stock for my Moxon Vise. I've had pretty good luck with it but my last edge I think I was getting tired because my edge didn't seem to go down even like I think it should. Giving it another shot tomorrow and hope to get on to glueing and drilling I'll take some pics then because now it's just boards to bore so it might be boring. Quote
Llama Posted October 6, 2013 Report Posted October 6, 2013 Excellent! I have been wanting to know about these. I'm looking forward to pics! Quote
brooklyngohardwood Posted October 6, 2013 Report Posted October 6, 2013 Awesome, congrats! Is this your first jointer? If not, how do you find it compared to a more standard jointer like a Stanley #7? Quote
Tony Wilkins Posted October 6, 2013 Author Report Posted October 6, 2013 It's my first so can't compare. Also my first BU plane. Quote
Tony Wilkins Posted October 6, 2013 Author Report Posted October 6, 2013 Here's a picture of the beast: DSCF1410 by Texchappy, on Flickr I took of the fence this morning after struggling to get that last little bit off the high side. Used the finger fence as I saw demonstrated by Schwarz in one of his videos. Seemed like I had a lot more feel. Knocked it down in no time. Don't mind the BU but after using it a couple of days I like my BD planes just slightly better. It'll be interesting (at least to me) to see if that continues. 2 Quote
Eric. Posted October 6, 2013 Report Posted October 6, 2013 What angle do you have on the iron, Tony? I don't know about the Veritas, but my LN low angle jack came with a 25* bevel. That's perfect for end grain but it's not right for pretty much anything else. You need to get yourself an extra iron and put a secondary bevel of 40* or 50* on it. That'll give you much better results. Unless you're just struggling with the mechanics of jointing a 90* edge, in which case it's only a matter of practice and eventually you'll get it down...throw away that fence! Also, not to get you second-guessing yourself or anything, but I tend to prefer the bulk of standard bench planes when we're talking jointers. The BU jointers that I've played with in the past kind of felt...less than...for jointing a long or thick board. Quote
Tony Wilkins Posted October 6, 2013 Author Report Posted October 6, 2013 It does in fact come with a 25* bevel. There is definitely an aspect of it that's learning to use it. However, I'm doing a lot better at it than I thought I would. The question I guess I need to ask is: should I get a higher bevel for squaring the long sides and/or using it to level faces? I might end up getting a #6 to use as a part time try plane. If the weight and the tote of the LN #5 hadn't bothered me I'd really think of an LN #7. Right now though, the BU jointer is doing the job well. BTW, I've had garbage luck with vintage stanley type planes. Quote
Eric. Posted October 6, 2013 Report Posted October 6, 2013 It does in fact come with a 25* bevel. There is definitely an aspect of it that's learning to use it. However, I'm doing a lot better at it than I thought I would. The question I guess I need to ask is: should I get a higher bevel for squaring the long sides and/or using it to level faces? I would for sure...I did for my LN62. I sharpened the 25* iron to a razor's edge but I couldn't plane basically any long grain without tearout. Curly maple? Fuggetabotit. Low bevel angles are for end grain. 1 Quote
Llama Posted October 6, 2013 Report Posted October 6, 2013 +1 on this! ^^I have no idea why these manufacturers decided on a 25 degree angle. There are better angles that allow you to get more use. Experiment with different angles to get the most out of the tool. Quote
Tpt life Posted October 6, 2013 Report Posted October 6, 2013 25 is a long slope angle. You can hone a micro bevel more times before needing to regrind the primary bevel. Quote
Llama Posted October 6, 2013 Report Posted October 6, 2013 25 is a long slope angle. You can hone a micro bevel more times before needing to regrind the primary bevel. This makes sense Thanks! Quote
rodger. Posted October 6, 2013 Report Posted October 6, 2013 I have the Veritas jointer and I love it. Check out my review, I posted it a whole back. I use the fence, and I also did a separate review of it. I am a big fan of bu planes. In fact, I was thinking about getting the bevel up smoother or LA smoother to add to my arsenal. Quote
G S Haydon Posted October 6, 2013 Report Posted October 6, 2013 Tony I cant certainly feel your pain with vintage metal planes, that sole wants to be very good indeed, if its out that's a whole lot of grinding. That's why I went wooden.... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.