Llama Posted October 12, 2013 Report Posted October 12, 2013 Sorry Sam, we love your table! Indeed! Quote
..Kev Posted October 12, 2013 Report Posted October 12, 2013 Sorry Sam, we love your table! Hell yea! Quote
pghmyn Posted October 12, 2013 Author Report Posted October 12, 2013 Mel that was hilarious, Sam is gonna cry in the morning!My handwriting may be dainty, but my emotions are tougher than steel!!!!! Only time I cry is when there are gaps in my dovetails. 2 Quote
Llama Posted October 12, 2013 Report Posted October 12, 2013 My handwriting may be dainty, but my emotions are tougher than steel!!!!! Only time I cry is when there are gaps in my dovetails. Excellent! Quote
pghmyn Posted October 16, 2013 Author Report Posted October 16, 2013 It's been awhile since I've had a moment to work on my table. I just picked up the wood for the legs today. They didn't have any shorts available that were long enough to make legs out of, and so I was going to buy a 100" long, by 9" wide piece of 8/4. I thought about it, and I didn't need that big of a piece. It was going to cost me over $50 anyway for it. So, I opted to get precut and dimensioned leg blanks for $40 total. Yeah, I paid a bit more if you go by board feet (or m3 for Graham). However, the amount of time saved for me to acclimate, joint, plane, and dimension, is worth it for right now. Especially since moving along with the project all depends on the legs being done right now. Also, having most of my free time taken up by school right now, every second saved is worth even more for the shop. Sorry for no real progress up dates. But here's my wood Quote
pghmyn Posted October 17, 2013 Author Report Posted October 17, 2013 I finally bogged my table saw a little bit down today. I guess the 8/4 oak was just too much But, in it's defense, I was feeding pretty fast. I have to figure out a good height for the table now, and get on with my progress. I can worry about the height and tapers later on, because I can just cut a little more off if the legs are too tall. Right now I am going to focus my attention on the mortise and tenon joints Quote
pghmyn Posted October 17, 2013 Author Report Posted October 17, 2013 A bit unconventional probably, but I did my tenons a bit different. My chisels are just terrible at holding at edge, so hand chopping eight 1" x 5" x 1/2" mortises would be a terror with sharpening. I cut one mortise today, and I am semi-pleased with it. My method was to mark out the edges, drill out as much material as possible with my hand drill, and finally clean up the sides with a 1" chisel. Getting into the corners would take forever, so I left the "scrap" in there, and cut out bits of the tenon to make it fit. Here is what the one I did just now looks like: The fit is absolutely superb with regards to width of mortise and tenon. Slides in, and I can hold it upside down without falling out. Now I just have seven more to go Although, the mortises for the front wont be bad at all since they will only be about 1/5 the size since they are the rails (or still considered aprons?) for the top and bottom of the drawer. Some small bits of cleaning up to be done on the tenons, but I am pretty happy overall. Quote
G S Haydon Posted October 17, 2013 Report Posted October 17, 2013 Awesome Sam, thanks for showing us your wood Great progress BTW. Nothing wrong with removing some stock with a drill, a perfectly acceptable way of doing it. 1/2" mortices are close to boring as a preference for many woodworkers anyway. Thanks for remembering the metric system too . Not essential at all, but a haunched mortice and tenon would of been ultra sweet on the top rail although your joinery will be plenty strong enough without it. Quote
Llama Posted October 17, 2013 Report Posted October 17, 2013 I'll add that a dowel jig would make it a bit easier to drill the holes, making sure they are straight and in line. Looks like you did a fine job though! Quote
pghmyn Posted October 18, 2013 Author Report Posted October 18, 2013 I'll add that a dowel jig would make it a bit easier to drill the holes, making sure they are straight and in line. Looks like you did a fine job though!A bench top mortises would be pretty nice too! But, I think I'm going to save my money for a router and eventually use that to make mortises. Money has been scarce for tools, so I'll have to make due for a while longer P.S. Remind me never to chop half blind dovetails in red oak again. At least not with the chisels that I have. Talk about excruciating. Good thing it was only for one drawer. I'm thinking about asking for a couple Stanley socket chisels for Christmas. The LN would be nice, but I would only be able to get one. Stanley SH is a good second choice here from all the reviews I've read. Quote
Freddie Posted October 18, 2013 Report Posted October 18, 2013 I love my ln chisels, theyre like my little pookie babies haha. Idk about the irwins, but i would look into them as well. Doucette and wolfe were using them for a long time, and if theyre good enough for them, then theyre more than good enough for us mortals 1 Quote
Byrdie Posted October 21, 2013 Report Posted October 21, 2013 The mortise and tenon shown are done quite nicely. It's important to remember that, as a basically hidden joint, fit and function are much more important than appearance. The work done is more than adequate and I'm sure you'll end up with a piece that will last for years. 1 Quote
pghmyn Posted October 22, 2013 Author Report Posted October 22, 2013 Good news...bad news (or bad luck?) The good news, I traded in my iPhone 4s for the new iPhone 5s. I got $173 for my trade in, and after further discounts I paid $10 for my new phone. Not bad. However, since I take all my pictures with my phone, that is where the pictures happened to be stored. I have iCloud on automatic backup, but it is not a continuous backup. It happens every few days. It just so happened that I got my phone previous to the backup. S#&* happens. This project was a rather simple one, and once the joinery was cut it was put together that night. The finish was applied, and it looks nice. I chose to use clear shellac. I am on my second coat now, and will put a third on the top. I am considering poly on top, but I haven't found it to be really necessary for this table, so I might not. Here are the pictures that I have of the finished product, but without the handle. In the first picture, look at the drawer front. Can Red Oak be curly? Quote
G S Haydon Posted October 22, 2013 Report Posted October 22, 2013 Very nice job Sam, very quickly turned around too which is very impressive. I think the red oak looks quite nice too and the drawer front looks sweet. The only thing that catches the eye is the DT's, very very neatly done but the spacing looks a little off. Overall a top job, hope you don't mind me mentioning the DT's? Quote
pghmyn Posted October 22, 2013 Author Report Posted October 22, 2013 Very nice job Sam, very quickly turned around too which is very impressive. I think the red oak looks quite nice too and the drawer front looks sweet. The only thing that catches the eye is the DT's, very very neatly done but the spacing looks a little off. Overall a top job, hope you don't mind me mentioning the DT's? I'M NEVER SHOWING ANYTHING AGAIN! Nah, I feel they look a bit odd too, even with the sizing. My smallest chisel is 1/2" and the beveled edges aren't really beveled too well. Makes for a clunky approach to cleaning the dovetails, so I oversize them as much as possible. Also, I eyeballed these for the most part. Only line I scribed was for the depth of the pins and tails in reference to the other board. Thanks for the love EDIT: I think the end grain on the front blended in quite well! Quote
G S Haydon Posted October 22, 2013 Report Posted October 22, 2013 Thanks Sam, I'm relived the feedback was OK! As for the end grain I didn't notice it because it looks just fine and from my perspective the overall proportions are very pleasing indeed. Quote
pghmyn Posted October 22, 2013 Author Report Posted October 22, 2013 Is the drawer front curly, or is it just my wishful thinking? Quote
G S Haydon Posted October 22, 2013 Report Posted October 22, 2013 I have no idea! But it sure looks that way . Quote
pghmyn Posted October 22, 2013 Author Report Posted October 22, 2013 Now that I built this table, the other half wants a matching set for the sides of the bed in cherry. 1 Quote
pghmyn Posted October 22, 2013 Author Report Posted October 22, 2013 Without getting too sentimental about this, I delivered the table today, and the look of joy in my grandma's face was priceless. But, when I told her it was made from my grandpa's wood, the look in her face was just that much better. You could tell that she absolutely loved it. It was a good day. 2 Quote
brooklyngohardwood Posted October 23, 2013 Report Posted October 23, 2013 Looks great! I'm not normally a big fan of red oak but I think this came out really well. One of my first projects I started with hand tools was a small step stool in red oak where I had to hand mortise all four legs—I gave up after a half a mortise and have been working on my skills in pine. Quote
pghmyn Posted October 23, 2013 Author Report Posted October 23, 2013 Looks great! I'm not normally a big fan of red oak but I think this came out really well. One of my first projects I started with hand tools was a small step stool in red oak where I had to hand mortise all four legs—I gave up after a half a mortise and have been working on my skills in pine. Believe me, those mortises were sent straight from the devil with my low quality chisels. The edge was gone after a few good chops. While the edge was there, it wasn't too bad. With a better set of chisels I can see this process to be much more enjoyable. Quote
Byrdie Posted October 23, 2013 Report Posted October 23, 2013 After all the discussion of the grain direction it turned out just fine. I still think it's natural to prefer it run side to side but I like the presentation on this piece and you did a nice job of lessening the effect on the front. Basically can't add anything to Graham's comments. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.