Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Building a really flat assembly table

Featured Replies

Hey gang,

I'm looking to build a "perfectly" flat assembly table that will also serve as a large out feed table for my tablesaw. I've been considering building the torsion box Marc built but I have a pool table that I want to get rid of and I suddenly thought what could be flatter? I think it is about 1 inch thick slate. Does anyone have any ideas on how to go about building this or has anyone ever heard of using slate for this purpose. Any suggestions would be welcome.

Not slate but I used to have a granite table was so heavy I just left it in the shop when I sold it. Your assembly table does not need to be dead flat your joinery needs to be square.

It seems to me that slate would be rather brittle. I would be hesitant to do any banging on it. Other than cleaning glue off of it, I don't see any other problems.

Slate would not be my first choice.  If you're using a sled on your table saw, the table would have to be below the level of the saw.  However, you could laminate a top to it that you could cut grooves in..

 

The torsion box Marc built is very flat with all the flexibility that you're looking for.

I prefer a flatter surface for assembling and checking for any rocking of a piece. A flat surface will determine that right away. I do not have an assembly table, or a good bench, so I use my table saw. Slate is definitely tricky to determine whether or not it's a good candidate. Assembly usually involves a rubber mallet or dead blow to drive home joinery. It might be wise to build a leg system with a plywood top that could provide full support under the slate. I'm thinking in terms of a tile floor. If a tile is fully supported from underneath, dropping something on it shouldn't break the tile. A hollow spot underneath could prove devastating.

  • Author

Thanks folks, you've givin me some things to consider. I think I'll remove the top few layers of plywood and MDF from my current assembly/outfeed table which will lower the hieght of the top. The base is quite solid and should still provide full support for the massive piece of slate to prevent cracking and handle it's weight. Then, as long as I top it with something like plywood or MDF to allow for extending the mitre slots from my table saw, I should end up with a fairly large and extremely flat assembly table. Sounds good in theory anyway.

The assembly table that we end up using the most is a 3' solid core door on cast iron leg/ends that I bought at an auction.  It doesn't move, and is very flat.

  • Author

I also have a bench made from a solid core door but after 20 years of sitting on a base that didn't give full support, it began to sag in the center. Not really sure if there's a way to bring it back to level short of turning it over and waiting another 20 years. I think the slate table will work better for me but I still use the door bench when I don't need to count on flatness.

I built a bench from a plan in one of the magazines (can't remember which, but there's plans and videos of it around). It's based on three layers of thick MDF laminated. So it's super flat, very cheap and easy to build. Pretty heavy though.

I built the torsion box 4 years ago and feel it's one of the best tools in my shop.  It get's a lot of use and is dead flat

  • Author

I actually have an assembly table that used three, 3/4" sheets of MDF that worked ok but it wasn't dead flat. I considered building the torsion box that Marc shows in his video but decided to kill two birds with one stone by getting rid of this old pool table (that is so flat I can't fit a one thousandth feeler gauge under the straight edge) and trying to use it as the top for the base I already have.

Turns out that this table is comprised of two pieces of 1/4" slate with a honeycomb material and wooden frame sandwiched between the slate. I am in the process of cutting it down and reducing the size of the frame to fit the base of my table. This couldn't be better for me because it reduces the overall weight of the bench and still gives me that dead flat surface.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.