Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bandsaw woes, it's drift but not as we know it...

Featured Replies

I recently after much waiting finally got a bandsaw. The model is a Bernardo HS 350 N (14 inch ). 

 

I ran threw all the steps of setting it up....but have hot some major issues when it comes to re-sawing...

 

I have tried and tried to adjust the drift using the fence without success.... it keeps making a non linear cut.

 

giving up on the fence i decided that if the blade is 90 degrees to the table (which it is)  then i would just score a line on the piece i want to re-saw and do it free hand.

 

 

i though this would work....but no....

 

when i cut following the line i score on the top of the piece i'm re-sawing it looks like the cut is going fine , nice and straight..

but i after re sawing the piece i see the disaster .,..

 

the first maybe 3 or 4 inches of the re-saw is straight. but after that the underside of the cut is skewing way off...and its like the blade is bending inside the work piece and creating a straight cut on the top side and the lower part is skewed way off... resulting in a  massive skewed taper... And i have also noticed that the bending the blade inside the piece actually pulls the work piece up slightly and angle off the bandsaw table top...

 

 

has anyone had similar problems? i'm at my wits end with it...and decided to seek help here after destroying a piece of Zebrano.

 

the blade on the saw just now is the one that came with it, which is a 1/2 inch blade...

I'm thinking of ordering a new blade also to see if that will help...

 

Any information or suggestions is as always, appreciated. thanks guys and gals!

Is the blade the one that came with the saw? If so buy a better blade I found that a 3tpi deep gullet blade works best, people are going to say buy a Woodslicer and, I hear they are really good I bought one but the Olson I bought 2-3yrs ago hasn't got dull yet. When I bought my 14" Grizzly Ultimate with 6" riser block I used the supplied blade it was POS when I went to a 3tpi blade my saw resawed like I couldn't believe. 

If you have good tension then it is likely the blade. All it takes is slight dullness or a tooth slightly out it set and tr blade will not cut good. If the blade can't clear chips it will load up and get hot and ruin itself and your wood. That's why you want few teeth per inch so the gullet can be bigger.

Steve

The blades that come with saws are usually garbage.  You may be pushing a little too fast also.  I tried a Woodslicer and it dulled after only a few cuts.  Then I got a Lenox Diemaster for about the same price and it lasted far, far longer.  A 1/2" blade is about as wide as you want to go with that saw, which is plenty for resawing.  If you're happy with your saw and plan to do a lot of resawing, then you may want to consider a carbide blade.  Here's a cut with a Lenox Trimaster carbide.  1" though.

 

post-206-0-19187900-1382193676_thumb.jpg

Sometimes when the wood is tough to saw I will rip a kerf on the tablesaw in the top and bottom edge using a thin kerf blade before I finish the cut on the bandsaw. 3 teeth per inch quality resaw blade and careful set up is also crucial. Square the table to the blade, check the tension and practice. Maybe some tough but inexpensive wood like oak to practice on?

Listen to Rick, do the 1/2 blade 3tpi. Let the blade do the work, don't force the cut. Sometimes stress in the wood can work against you and the fence. I will sometimes stick a small shim after several inches of a cut in the kerf (think of it like a table saw splitter) Helps me.

 

Just keep practicing you'll be fine!

 

-Ace-

I'm sure the blade is part of the problem but I think this sounds like blade tension and feed rate are also a factor.  I have to work on it myself but pushing to hard to speed up the cut definitely effects cut quality.

So I'm a new guy to real bandsaw as I just got a 14" myself, wouldn't the 3/4 blade be better for resawing? I'm still working with my factory blade, but overall I'm much happier with this one than my 10" bandsaw!

The frame and spring in most 14" bandsaws is not strong enough for a 3/4" blade to be tensioned properly even if your motor has enough horsepower to turn it. To resaw on a 14" bandsaw use a 1/2" 3 teeth per inch blade, many different ones are available. I use a"Woodslicer" from Highland because they are just down the street from my shop. Timberwolf blades also work well for me.

The most important thing is to tension and adjust the guides on your saw, fine tune it! Cool blocks work better than the metal ones, bearing guides( like the ones from Carter) work even better in my opinion.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.