CessnaPilotBarry Posted March 7, 2014 Report Posted March 7, 2014 Hey all... Based on an upcoming project and not looking forward to M&T'ing the particular parts involved with my usualy methods, I took the "plunge" on a DF500 Domino kit with the cross and trim stops, and the cutter / Domino kit. After reading through the manual, watching some Festool videos, and generally playing with the tool, it seems mostly obvious... Anybody want to share any lessons they've learned in the time spent with yours? Thanks in advance! Quote
..Kev Posted March 7, 2014 Report Posted March 7, 2014 Wdwerker suggested the domiplate - I haven't ordered it yet but, looks very useful to do with your new domino. http://www.senecawoodworking.com/products/domiplate-for-1-2-and-3-4-ply 1 Quote
Trip Posted March 7, 2014 Report Posted March 7, 2014 Have you've you seen, "Getting the Most From the Festool Domino Machine" by Jerry Work? It's too large to attach to a post, but you can probably Google it... If you can't find it anywhere, I can eMail it to you. Quote
PaulMarcel Posted March 7, 2014 Report Posted March 7, 2014 From Festool USA's blog: The Ultimate Festool Domino Guide Jerry's article is listed there to download the PDF. There are also plenty of tips-n-tricks videos in the list besides reviews. Quote
Tom Crawford Posted March 7, 2014 Report Posted March 7, 2014 Jerry's document can be found here http://www.jerrywork.com click on "How To. . ." Rick Christopherson also has an excellent manual on the Domino as well as other Festools http://www.waterfront-woods.com/festool/ Quote
CessnaPilotBarry Posted March 7, 2014 Author Report Posted March 7, 2014 Thanks, all! I appreciate the recommendations. Quote
STL Woodguy Posted March 7, 2014 Report Posted March 7, 2014 As with most Festool stuff, the manual is useless, hit the website for the supplemental one instead. Tempting to plunge quick - especially if you have a lot of mortises to do - but when first using the tool, take it nice and easy. The Domino is still prone to human error and slippage. Grip and plunge in from the back of the unit (closer to the power cord), not the front. As you get the feel down, the speed and efficiency comes. Just verify that the little plastic window on the fence is true. Paul Marcel has a video, and the Festool Domino supplemental guide discusses calibration too. Typically when using multiple dominos in a line to connect a shelf, top or whatnot, I'll plunge one precise mortise on one end, then wider ones on the others. Just in case you don't plunge precisely, it affords you a little wiggle room. Sand some dominos down, color them to identify them and keep them to test dry fits. Dominos are tight and you'll be reaching for the plyers a lot when disassembling. OH, and when placing a Domino to prepare for joining, put it on the side that has sufficient material past the mortise like on the sides of a board. If, say, the mortise is on the face of a sheet of plywood and you try and push the joining board into that, there is a high probability that the Domino could punch through the wood and vaneer if forced (as a dry fit / mallet does). Uh...not that I would know that or anything.... You did good buying the Domino cutters / kit. Yes, an extra purchase pain, but when you add up all the dominos and price of cutters, it's more cost effective. Quote
patriot Posted March 9, 2014 Report Posted March 9, 2014 When I first started I had some problems with my alignment. I was testing it out on smaller stock which wasn't secured well enough. Since I wasn't familiar with the tool and I was dealing with my work piece moving around a bit I was constantly adjusting the direction and amount of force I was applying with each of my hands. This resulted in mortises which were either loose, or didn't enter perpendicular to the work piece. After analyzing things and some practice, I determined I needed to: Use a back stop (or clamping) to provide some resistance to the direction of plunge. Apply consistent downward and inward pressure with my support hand so the Domino is firmly and properly registered against the work piece so it won't move during the plunge. Make sure the plunge is going directly into the work piece at a slow, consistent rate. (On my first cuts I was actually applying some downward pressure on the back of the tool during the plunge which was causing the front of the tool to lift slightly) I would recommend making your first test cuts on boards that are large enough to register the entire face of the tool on before you move on to smaller/narrower pieces. UPDATE: Forgot to mention... After getting comfortable with the Domino, I no longer need to use a back stop. Quote
wdwerker Posted March 9, 2014 Report Posted March 9, 2014 I often cut mortices on the first width setting and slightly sand the little ridge off the side of the dominoes. I use my osselating belt sander , just a touch on each side does the trick. This gives you a little bit of adjustment to flush up the edge of a joint during assembly and a place for excess glue to escape. For small width parts that won't hold 2 dominos side by side I cut the mortice at the widest setting and make my own domino stock to fit. Rip a strip just a bit bigger than needed and plane or drum sand down to exact size. Then I round the corners on the router table. It takes a bit of setup work so I run a bunch of strips when I am set up. All the wood comes from the scrap pile . Dial calipers are your friend when making your own domino stock. If you don't have one just keep testing the fit in a domino mortice . Cut your test mortice in something hard so the hole doesn't wallow out from constant testing. Some rules of thumb for figuring out how to fit dominos into a joint. Leave at least the thickness of the tenon above and below a mortice in the thickness of a board. So a 3/4" board is about 19 mm that means a 5 or 6 mm domino, a 1" board is 25mm so an 8 mm domino max. Leave at least twice the thickness of the size domino you are using undisturbed between dominos and from the ends of a board. I usually start with the pin or flippers in from each edge of a board and then divide up the space left in between. I can double stack (2) 8 mm dominos in a 8/4 board edge. (3) 8mm spaces undisturbed wood and (2) 8mm domino mortices equals 40 mm or a tad over 1 9/16 thick. Quote
CessnaPilotBarry Posted March 10, 2014 Author Report Posted March 10, 2014 Thanks, all! A bunch of poplar died for a good cause this weekend... The aftermarket manuals you've suggested have been great helps. I've printed out all of your other tips to keep in the Systainer as I continue to practice, and have already used some of them. Quote
wouldwurker Posted March 14, 2014 Report Posted March 14, 2014 Hey man. I just got my Domino 500 last week. Thought I had it figured out, then the supplemental PDF manual and the 'getting the most...' PDF online blew my mind! Like you, every 2by bit of scrap I could find was plunged throughly Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.