Recommended Posts

Posted

So I finally put the Resaw King blade I got on my saw.

 

It isn't tracking quite right, wants to track 1/8 of an inch to the left.  Thought it was tracking correctly for awhile, then tried to resaw a 6" piece. The cut slanted, blade is pushing out on the bottom.  The 1/2" blade I had on there would resaw better than I am getting now.

 

All my guides look good.  Played with the tension, but that didn't seem to do much.

 

 

Thoughts?  

 

Josh

Posted

==>The cut slanted, blade is pushing out on the bottom

==>Played with the tension, but that didn't seem to do much

 

Your description screams blade tension.

It could be a defective blade, but I talked to the guy who actually QC inspects them at the Laguna plant -- they have a very low defect rate...

 

How did you determine tension?

Posted

I guess we are the only people thinking about Wood on a Saturday night!

 

Just by feel and 1 measurement below 3/4" on saw tension readout. How much defection on a blade like this?  3/4"

Posted

==>I guess we are the only people thinking about Wood on a Saturday night!

Yea, wife is out of town, so I'm just watching some Dr Who on one monitor and surfing on the other... I'm only allowed to watch Dr. Who when the wife's not within earshot...

 

Little more data -- what saw?

Posted

I guess we are the only people thinking about Wood on a Saturday night!

 

Just by feel and 1 measurement below 3/4" on saw tension readout. How much defection on a blade like this?  3/4"

 

 

If you are saying that when tensioned you can deflect it 3/4" that may be your problem.  I tension mine so deflection is under 1/8" 

 

No He is talking about a window (tension indicator window) on the back side of the saw, it's a scale to give you a idea of the right tension for the blade size.

Posted

I wouldn't rely on those gauges. They rely on an exact blade length. On resaw king, even one tooth too many or too few and that gauge reading will be way off. There was a WTO thread on blade tensioning... no time was reading the gauge recommended. Essentially PB and I got into a debate --- I seem to remember PB winning...

Come Back PB!... Come Back PB!... We Need You... Come Back*... 

 

 

*Category: Obscure '50s pop culture references...

Who is Joey? Correct for $200...

 

Any guesses? Google is strictly forbidden... Especially because I'm doing it off the top of my head and I don't want to be caught-out because I know the quote isn't exactly spot-on...

Posted

I know you wasn't calling me out, but I did say "a idea of the right tension"   I think I will edit the post and bold IDEA. lol

 

Yes, it will good to have PB back, He is very helpful, like you and many others.

Posted

==>a idea of the right tension

If the blade length is even 1/4" from factory standard, then it won't even get you to the ballpark... I know first hand... I had four timberwolf blades between 1/4 and 3/8s out... I couldn't get the blade gauge to even register on the scale... True story... I think that's how the previous thread got started... Timberwolf re-cut the blades and sent them back in less than four business days... They even paid postage both ways...

Posted

I got it figured out.  Had to adjust the lower wheel.  This blade cuts really well.  

 

Might need a little more fine tuning but I am in business.  I have some long off cuts 2 X 12 SYP I am going to use to make a small hand tool chest.  

Posted

==>Had to adjust the lower wheel.

Glad you got it worked-out. I'm not familiar with your saw... What is 'adjust the lower wheel'?

 

==>This blade cuts really well.

Yea, I really like mine... I use an inexpensive ($35) timberwolf blade for most resawing until I need to process Hard Maple or exotics -- it really shines on things like Bloodwood... 

Posted

I had to do this.  http://www.highlandwoodworking.com/library/manuals/rikon/rikon_lower_wheel_adjustment_guide.pdf

 

Fixed it immediately.  

 

 

==>Had to adjust the lower wheel.

Glad you got it worked-out. I'm not familiar with your saw... What is 'adjust the lower wheel'?

 

==>This blade cuts really well.

Yea, I really like mine... I use an inexpensive ($35) timberwolf blade for most resawing until I need to process Hard Maple or exotics -- it really shines on things like Bloodwood... 

Posted

Having some problems with the blade deflecting out different times during the cut.  I end up with a wavy piece of wood.  Can't tell if it is my feed rate or blade tension. I really have the thing tensioned down, so I don't think that is it.

Posted

No one has mentioned table:blade squareness or drift.  Have you addressed drift?  Also, is your workpiece square?  If you're trying to resaw a piece with a less than perfect 90* edge, this can cause a wavy cut, too, because you'll try to keep it flat against the fence but its inclination will be to tip away from or into the fence, depending on the angle of the edge.  Make sure it's dead square.

 

Everything has to be pretty much dead nuts dialed in when you're trying to resaw or it ain't gonna work.

Posted

==>Everything has to be pretty much dead nuts dialed in when you're trying to resaw or it ain't gonna work.

+1

 

Human nature is a funny thing... Folks are mostly on auto-pilot -- we just assume the 'obvious', but it takes four days before anyone actually asks the question... Bet the shrinks have a term for the that... Any shrinks in our studio audience?

Posted

I have not had time to mess with it for a few days.  I think I know what is wrong.  I will continue to fine tune it.

 

Sure I will have more questions though.

 

Josh

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 57 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined