collinb Posted September 23, 2014 Report Posted September 23, 2014 It's a Delta. Used it for the first time a couple of weeks ago just to get a handle on it. When I bought it I was told about planer behavior but not of a technique for dealing with it. Specifically, the board I fed through it earned a concave spot near the end. So how does one feed a board through and avoid that? I was thinking of feeding another piece immediately ahead of the target board. It seems that it would also need to be attached to control any lifting of the front of the target board. Another thought was to lift the back end just slightly and flex the board so that it feeds straight and the tension of being slightly bowed would remove any tendency of the front end to lift up. What's the proper technique/best practice? Quote
RichardA Posted September 23, 2014 Report Posted September 23, 2014 I'm no expert, but it sounds to me like your infeed side is set to low. Try raising the infeed table to where there is only 1/16 or 1/8 of a difference between them.... Lay a straight edge across both tables and see how much you have to move the infeed side up to get a smaller gap. Quote
minorhero Posted September 23, 2014 Report Posted September 23, 2014 2 possibilities, one, your blades need to be sharpened. And two, your pressure bar is not set correctly and needs to be adjusted. Its called snipe, and there are videos and articles all over for dealing with it. Quote
minorhero Posted September 23, 2014 Report Posted September 23, 2014 @RichardA, I think the op means a planer not a jointer. Planer tables are set at the same height. 1 Quote
RichardA Posted September 23, 2014 Report Posted September 23, 2014 @RichardA, I think the op means a planer not a jointer. Planer tables are set at the same height. Damn,.... see what to long in the shop does! I went out there at 3:30 this am and read his post totally wrong.....gonna take a nap. Thank's for pointing out my error! 1 Quote
Coop Posted September 23, 2014 Report Posted September 23, 2014 Collin, does your planer have in and out feed tables on it? Quote
collinb Posted September 23, 2014 Author Report Posted September 23, 2014 K Cooper, I will check. I will also take the initiative of downloading a manual for it. As a last resort perhaps I should also read the instructions. 2 Quote
Tim Kohl Posted September 23, 2014 Report Posted September 23, 2014 there is an excellent discussion on snipe already posted in the forum. Due to my inability to figure out how to post the link search snipe and click the link. Quote
RichardA Posted September 23, 2014 Report Posted September 23, 2014 K Cooper, I will check. I will also take the initiative of downloading a manual for it. As a last resort perhaps I should also read the instructions. Reading instruction's is a good way to start, and it shouldn't be the last resort, it should be the first! Quote
wtnhighlander Posted September 24, 2014 Report Posted September 24, 2014 Most portable planers have beds that are way too short for proper support. Adding infeed and outfeed support tables that keep the stock flat as it passes under the cutters will go a long way towards eliminating snipe. If had space for it, I would build a melamine 'auxilliary' bed for my planer, that passed all the way through and extended about 3 feet one each end. Quote
collinb Posted September 24, 2014 Author Report Posted September 24, 2014 RichardA, I was hoping that the irony would be obvious. :-) wtnhighlander, Mine came mounted toward the end of a home-made table. On the short end is most of a foot of table. On the back end is about 5 feet of table to receive the board. Being new to woodworking I had not yet head the term 'snipe' before. Thanks for the key to the issue. I had considered cutting of board ends. That would be, well, practical. Quote
wtnhighlander Posted September 24, 2014 Report Posted September 24, 2014 Since you already have the outfeed table, you can minimize the snipe on the front of the board by simply holding up the tail end as you feed it through. Quote
collinb Posted September 24, 2014 Author Report Posted September 24, 2014 My thoughts exactly. Just add a little arch to it for tension but keep the front flat.. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.