Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Mobile Base for Monster Bandsaw

Featured Replies

Hi there,

I printed out the pattern for the laminated sides and made a cardboard template. I found that I had made a mistake in the placement of th end rail and had shortened the base by 1-1/2". The base of my saw would not have fit. I have fixed the problem and now the sides are going to be 48"x6". Attached is a image of the final template for the inner rails and it can also be used for the outer rail just without the holes. Also I found out by reading my shipping invoice that Rockler had sent me the 3" wheel castors not the 4" because they believe that the smaller wheel is stronger. We will see. And if they fail Rockler is going to refund my money and ship me the 4" wheels. 

I went to Lowe's to get a countersink drill bit which they were out of at the time. I looked at he 3/4" Baltic Birch plywood and found a piece that was missing a 3"x2" bit at a corner. I had seen the department manager just minutes before going to the panel goods aisle. As I was going towards him I also saw 1-side sanded maple 3/4" that was missing a Dutchman near one end standing up in the aisle so I loaded it up onto the cart. I got the department manager's attention. He came up the aisle and met me and I pointed out the flaws to him. I asked him if he would get me a deal on them if I took them both. I told him that I had a project that would allow me to work around them. He said that he could do around $30 for them. I asked if he could do $25 since they were out of the countersink bits that I came in for or would he just cut them up for smaller panels. He said that the smaller panels didn't sale well and they he could do $25. I ended up having them cut into 4 4'x4' panels so they would fit into my van. I even got a can of spray paint that is suppose to match my DeWalt tablesaw's yellow. All in all a good trip to the Grey and Blue Big Box Store.

Hopefully tomorrow I can get a panel of the maple cut into 8-48'x 5-7/8" strips and cut the mortises decking and the end rail. I had thought about using the router to connect the decking mortises after making starter holes with the hollow chisel mortiser but now think that I will use the mortiser to make all of the mortises. I plan on using the dado stack to make the rabbit in the end rails. My plan is to glue up the inner rails and outer rails separate then glue them together. Then true up my mortises. Next glue in the end rails and the decking. Finally add the wheels with through bolts.

 

Should I put carriage bolts with fender washers through the base or countersunk screws?

 

Chef

I agree about the mortise. That curve is the critical part to the whole base and the most likely to fail. I would not only not put the mortise there but make the whole thing thicker at that location. Consider skipping the mortise and use a simple but joint on the end to attach your side rails. You will have edge grain to edge grain so it would be strong enough. But it would require getting rid of the curve on the underside and just going with 90 degree cut.

There is also the possibility that you won't get a break but the wood will bend the 1" or so that is needed for your machine to touch the ground. That can happen as well and is one reason why a lot of folks stick with metal for bases, especially ones where the machine is going to be suspended all the time.

I will go contrarian. Since you are laminating ply for these rails, just be very careful with the tenon to leave enough ply to satisfy the load requirement. Consider a third layer of ply (I did read this and am not imagining things, right? Multiple threads?) just to have enough thickness to receive the tenon.

  • Author

I gave this to my engineer buddy who works at CAT. If we make it a but joint with three screws. It will have 97% the load carrying of the mortise and tenon. So I will be changing. Thank you all for your input. The point of failure when every the base was racked by a force was the tenon busting out he front of the laminated rails.

I am getting ready to cut my first inner rail out tonight. How would you cut the mortises for the bottom decking? I have both a hollow chisel mortiser and a router with a 1/2" spiral bit. I was going to use the router with an edge guide and clamp on a jig to limit the size of th routed hole. Or just make all of the mortise with the mortiser?

 

Chef

With screws into end grain or ply edges I would reinforce with epoxy. Failure here is the number one failure I see with racking forces and is fairly easy to prevent.

  • Author

I got the first of the copies of the laminations cut on the bandsaw. I lover how the big motor just plows through the wood. The bandsaw thought of the plywood as cardboard. It jud zipped right along. I am finally getting tired so I will head off to bed. See you tomorrow.

 

Chef

I got the first inner rail marked up. I found that I could not see the pencil lines and had to go back over them with a Sharpie. So I guess that I need to put some more lights in my garage shop. I have to two t-5 46" lights over the front of the garage. How many lights do I need to add.

Chef

.

I found my problem not only being the lighting but needed a stronger pair of Walgreens reading glasses

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.