Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

router workpiece edge blowout. how to prevent?

Featured Replies

When I'm routing a piece of wood, hard or soft, I have to pre-score/saw/chisel the points where the router bit exits the workpiece.  I know that sounds vague so I'll try to be more detailed.  Let's say I've got a piece of wood one inch deep and four inches wide.  I want to do a straight routed "notch" right through the board at a 90* degree angle at 1/2 inch depth.  When I start into the board routing freehand with a fixed base, everything is cool.  When I get to the other end of the board it chips the edges of the workpiece where it exits the cut.  Splinters, nicks, or even quarter inch chunks can get thrown out.  Is it because I'm using low quality budget bits, or is there some trick/method I don't know?

 

Up to this point my thinking is to start into the board and go halfway into the cut, then switch sides and start routing the board from the other side, meeting in the middle.  I haven't tried it yet, and I can't help but wonder if there will be tear out in the middle of the board as there is with a straight-through pass.

Use a scrap backer board to reduce the tear out.

  • Author

Use a scrap backer board to reduce the tear out.

 

I'm sorry, I'm a router newbie.  I'm used to framing houses--not fine woodworking.  Could you help me understand what you mean?  I apologize, but I'm just getting started.

Around the three minute mark.

If you are holding the router in hand, it becomes clamping the board to a "fence." Just takes a little thought to flip this upside down. When the router moves the pieces have to be "clamped."

A backer board is your best option like Tiods and c Schaffer suggested. You can also use some blue painters tape that you cut through to reduce small tear out. Nice sharp router bits will help your problem out as well.

Sent from my iPhone using Tapatalk

Shaffer's video is spot on..  I don't like the board he's using as it looks all chewed up but, that's what we're talking about.  In essence, you're supporting those fibers on your piece with some scrap that you don't care about.

  • Author

Shaffer's video is spot on..  I don't like the board he's using as it looks all chewed up but, that's what we're talking about.  In essence, you're supporting those fibers on your piece with some scrap that you don't care about.

 

Thanks for all the useful tips everyone!

One other option..... Stop your cut before you reach the end... then start from the other side .... Clean cuts on entry, so enter twice   once from each side!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.