Anne Sansone Posted December 28, 2014 Report Share Posted December 28, 2014 My house has a built in dining area. I't about 30 years old and hasn't been well taken care of. There were gashes and dark rings, and it was just in horrible condition. The front door is made by the same artist and saving the table is super important to me. So, I'm re-finishing it. There are different types of wood, and I had to bleach out the dark rings. The picture with the window in it is another problem area. Most of the table is sun-bleached, just not that strip on the edge. I know it looks like a shadow, but I promise it's not. So, I removed the finish and hand-sanded the whole thing making sure to go with the grain, I bleached out the black rings and am bleaching the surrounding area to blend it in. So my question is this... How do I stain this thing to get the main colors as even as possible, while maintaining the different shades and grains of the inlays? I don't have any before pics but this is where I am now. 1 Quote Link to comment Share on other sites More sharing options...
Tpt life Posted December 28, 2014 Report Share Posted December 28, 2014 Shades are going to show up wet. I would wipe the table down with mineral spirits to get a feel for whether any or how much color is truly needed. Welcome to the forums! Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted December 28, 2014 Author Report Share Posted December 28, 2014 Thanks for the tip and the welcome. I've been lurking for a while, Just haven't gotten stuck before now Quote Link to comment Share on other sites More sharing options...
RichardA Posted December 28, 2014 Report Share Posted December 28, 2014 Welcome, and now that you've "struck", Mr. Shaffer's suggestion is spot on! Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted December 28, 2014 Author Report Share Posted December 28, 2014 Ok, I couldn't figure out how to post the pic here on my update so I edited the pics above. It ended up not needing as much help as I thought it would but it's still pretty bad in the middle, and a little light on the outer edge (near the right of the photo) The only thing I can think of is to bleach the whole center area and stain that. Hopefully there's a better way? Quote Link to comment Share on other sites More sharing options...
wdwerker Posted December 28, 2014 Report Share Posted December 28, 2014 Stain is going to be a bad idea on an inlaid top. You can use "natural " stain which has no color in it to bring out the rich tones. A poly , oil ,shellac or varnish will add some Amber tones which may be what you are after. But please don't try to use colored stain, especially on just one area. It might be possible to use a very weak stain, like 9 parts natural to 1 part stain to slightly tint the entire top but be very cautious. Quote Link to comment Share on other sites More sharing options...
wtnhighlander Posted December 29, 2014 Report Share Posted December 29, 2014 Anne, it appears that most of the damage falls within thw "water" portion of the pond, correct? And it also appears that the leaves and stones sit slightly proud of the "water", correct? If that is so, you might be able to carefully brush a stain or dye mixture onto the " water" background to even its color, yet leave the remainder of the inlay as it is. I certainly would not recommend applying a color to the entire table, that would obscure the appearance of the inlay considerably. If the leaves and stones are actually flush with tbe rest of the surface, I wouldn't try this, as there is too much chance of the color bleeding into area where it isn't wanted. 1 Quote Link to comment Share on other sites More sharing options...
wdwerker Posted December 29, 2014 Report Share Posted December 29, 2014 If it's just the "water ring " that you are concerned with Google it, I saw a bunch of suggestions on how to remove them . Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted December 29, 2014 Author Report Share Posted December 29, 2014 The dark ring was a pain to get rid of, the bright white ring, (I had to bleach it out) is the new issue.The leaves are standing proud a bit. Maybe I can dilute some stain and just layer it as needed to blend in. Would it work the same way diluted as usual? i.e. Just repeat until It's the right shade? Quote Link to comment Share on other sites More sharing options...
wdwerker Posted December 29, 2014 Report Share Posted December 29, 2014 If you used an artists brush and layered it carefully it might work. Be aware that even if it looks pretty good when you stop staining it may still be visible after you apply a finish over it. Should look better than it does now but don't have high expectations. Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted December 29, 2014 Author Report Share Posted December 29, 2014 Aww, that's a real bummer. After the stain dries, and I'm happy with it is there any way I can check to see what it'll look like once the finish is on it? I have faith in my art skills, just a serious lack of experience. Quote Link to comment Share on other sites More sharing options...
Tpt life Posted December 29, 2014 Report Share Posted December 29, 2014 The white screams. An off color or change in texture may grab your attention. I think we all just want to be sure you don't have too great an expectation. I would probably try a thinned coat of shellac. It will bond to any stray old finish or glue. It can be wiped off with alcohol if something goes badly. It will cover with most any other finish you can dream. Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted December 29, 2014 Author Report Share Posted December 29, 2014 that's totally fair. I know it will never be like new, at this point I'll settle for passing. I'm not sure which Is worse. The original Black ring or this horrible white. At least I have a plan now. 1. Dilute stain and play with it til I get the color as good as I can. 2. Blend to the rest of area 3. Thinned coat of shellac to test 4. either Poly finish or wipe off and keep playing. 5. If all else fails, rebuild the table so the problem area is at least to the back Thanks for all the help! Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted January 1, 2015 Author Report Share Posted January 1, 2015 ok, That was horrible. It's better than the white, but not even close. I figured I've done this much already, and I'd like to get it right. New plan... lay veneer over the "pond" area.. What do you guys think? Quote Link to comment Share on other sites More sharing options...
Tpt life Posted January 1, 2015 Report Share Posted January 1, 2015 Are you willing to post a pic? Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted January 1, 2015 Author Report Share Posted January 1, 2015 but... it's so embarrassing! https://drive.google.com/file/d/0B3_CFi1qT9CyejdNNklGMmtVVzhoOENmaHJaNzVvUGRKc2ZR/view?usp=sharing here it is. Looks good from above but on an angle I get this Quote Link to comment Share on other sites More sharing options...
Tpt life Posted January 1, 2015 Report Share Posted January 1, 2015 So it is not perfect. It has been used. It will never again be perfect. So what is left? There is no tell tale ring. I do not see the tell-tale "wet or hot cup was set here." I do see some color variation but it is a pond. Are the edges of discoloration as blended as they appear to be? There will be a gloss to the finish that will trick the eye and obscure some of that raking view. This may not be quite as bad as you imagine. Edit: If you go for editing the veneer, do not try to replace the whole pond but rather creatively add a leaf or stone. It will cut your investment way down. Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted January 1, 2015 Author Report Share Posted January 1, 2015 The edges are blended pretty well, and I guess you're right, it is better than it was... Adding a leaf or stone is a great idea! I never thought of that. I was looking at veneer sheets and they're more expensive than I thought. If I did go that route would I need to do? Would I need a backed piece of veneer? What would I be getting myself into? veneering is a whole new realm of WW that I've never done. Quote Link to comment Share on other sites More sharing options...
Tpt life Posted January 1, 2015 Report Share Posted January 1, 2015 Same here. I am just trying to help you process thoughts. There are threads here on veneer if you work the search function and there is a lot available on YouTube these days. I think Marc even has a project on the free site. I will dig. You will want to focus on inlay as that is the process of excavating to apply a shape. If this kind of work is enjoyable to you, learning that process will be a valuable triumph. Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted January 1, 2015 Author Report Share Posted January 1, 2015 Honestly it sounds like it could be fun. I'll def. check out Marc's project, and look into this a bit further. I really appreciate the help. Happy New Year! Quote Link to comment Share on other sites More sharing options...
Tpt life Posted January 1, 2015 Report Share Posted January 1, 2015 http://www.thewoodwhisperer.com/videos/router-based-inlay/ This is just one way. There are strategies without a router also. Quote Link to comment Share on other sites More sharing options...
wtnhighlander Posted January 2, 2015 Report Share Posted January 2, 2015 Ahhhh, what your pond needs now are some koi fish! Use a veneer that closely matches the pond, and add some artistically simplified fish shapes to suggest koi / goldfish swimming beneath the surface. 2 Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted January 2, 2015 Author Report Share Posted January 2, 2015 If I could take the table with me I'd totally put koi in it! That would be awesome. Sadly it doesn't match the house and would be weird, unless I put fish other places too... I'm designing some leaves as I type and I'm thinking I'm going to carve it by hand. The router looks easier, but I don't have one and I don't have the attachment for my dremel. If I come back to it I'll probably invest in those tools. A RO sander is probably first on my list to get though. I love this board. Quote Link to comment Share on other sites More sharing options...
Anne Sansone Posted January 2, 2015 Author Report Share Posted January 2, 2015 inlays are in https://drive.google.com/file/d/0B3_CFi1qT9CyUjVocXFFM2t2QUpnOFpxVWVvQmlBOS1RZ00w/view?usp=sharing Quote Link to comment Share on other sites More sharing options...
..Kev Posted January 2, 2015 Report Share Posted January 2, 2015 Looks great! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.