Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

HF Gem?

Featured Replies

http://m.harborfreight.com/20-oz-hvlp-gravity-feed-air-spray-gun-with-regulator-69705.html#pr-header-back-to-top-link

Have any of you had any experience with this gun? I want to spray a few things before I commit to a $600 unit.

A friend sent me this link saying he has been using it with the 1.4 for years and loves it called it a real harbor freight gem. .

I'm trying to spray some oil based paint on a door.

  • Author

I've got a 40 gallon hooked to 1/2" id lines and fittings.

What is "Mill work" type stuff? Never heard the term.

I've got a 40 gallon hooked to 1/2" id lines and fittings.

What is "Mill work" type stuff? Never heard the term.

 

Gallons doesn't mean anything. 3-4 cfm per hp @40 psi that would need a 5hp compressor without overworking your compressor and getting consistent atomization.

You'll be fine if your spraying smaller things , but once you get into larger projects it doesn't perform so well . I have a 150 gallon  compressor and that struggles to keep up on bigger jobs .  BTW the Woodriver conversion gun is pretty much the same thing .

Lets just pretend that you are set up with a proper compressor and you are just looking for a gun to get going. A fellow painter at work told me his friend picked up one of these guns and said it works really good. 

That purple "Barney" gun is a piece of crap. Don't buy it. You will be taking it back 4 or 5 times, exchanging to get a gun that won't leak. I made 2 trips to the store for returns. After the second, I said forget it. 

 

The problem is the gun is made with cheap fittings and is a leaker.

 

Spend the money and get a decent gun!

 

-Ace- 

 

The guns sell for 12.00 with a coupon and without the regulator.

  • Author

6 real horses? Not likely. Motors usually go from 5 to 7.5 hp.

Steve

Steve, I don't know what the actual yield is. I've not taken the compressor and electric motor off and tested and I don't really care to I know that 6hp is stamped on it twice.

23 amps @ 230 volts converts closer to 5hp than 6, but that is a conversion from watts (heat energy) to hp (work / time). The conversion can be done in imperial units or metric units, producing different results:

http://en.m.wikipedia.org/wiki/Horsepower

I'm betting the mfg splits the difference.

I have a couple of them, they come with two different spray nozzles, you need to look at the pattern of air holes around the center material hole, the more expensive one has several atomizing holes and breaks the material down into a much finer spray, either will be fine for furniture. We use them mostly for primer and single stage paints in the body shop, when they start acting up just toss and replace, it's cheaper than seals for the good guns

I'm sure your compressor will be fine, unless you plan on spraying non stop for hours at a time, I use my 1 1/2 hp 12 gallon unit all the time on job sites, few jobs require more than 10-15 minutes of non stop spraying at any given time

  • 4 weeks later...

I have a good tip for you guys. If you're like me and can't afford a proper paint booth, or even a proper set-up to trap water I found a way to keep water out your air lines. When the air is compressed, the moisture in the air condenses in your compressor. If you look at a sherwin williams set up they'll advise running like 40 ft of hard line with multiple turns and filters to capture the water. Well what I did was take a cheap-o airline and coil it in a bucket that I then fill with ice water. I then pull the end out to a water separator and then a short 15 ft line from that to my gun. I have also have a small inline moisture filter attached to my gun.  Before I started using this process with the cold water I just had the disposable filters that screw into my gun and I'd go through one of those after just a couple of uses.  

Before I switched to HVLP I ran a 50 ft hose across the concrete floor and hooked a water separator between that and the hose to my gun. Also helps to drain any moisture in your tank before you start spraying.

I use this for water/oil filtering. Works great and uses single ply toilet paper as a filter element.  Remember, you want to filter oil vapor, as well as, water from compressed air lines. I also use an inline filter at the spray gun for just in case.  ;)

 

MOT-M60__97028.1407535742.1280.1280.jpg?

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.