Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Cocobolo high gloss finish

Featured Replies

1st time posting, long time lurker...

 

I had a good friend turn a bunch of cocobolo into speaker connector covers (see pic below showing a representation of what I wanted him to do) as I am building some cables right now for my listening room. I'd like to get a high gloss finish on the cocobolo as my speakers (Aerial Acoustics 6Ts) are a high gloss rosewood as well.

 

I've seen everything from shellac+wax to CA used for a high gloss finish.  I have shellac plus some very high quality car wax (Griots Garage Best in Show wax) that are already on hand. I've also seen EEE Ultrashine as a possibility, although its a cut n' polish which may not work over shellac. What have you all used or recommend?

 

RSC_d2_zpsa2d96dfb.jpg

Rattle can gloss laquer comes to mind first.

 

Yep..  Something like Deft.

 

Would be more work but, General Finishes Arm-R-Seal gloss might work well too.

  • Author

So something like Arm-R-Seal, I'm guessing after application to use a progressively higher sandpaper grit and then buffing at the end? The GF site says to use a paste wax...

You could but, you also might not need it.. 

  • Author

Ordered a pint of Arm-R-Seal (Gloss) last night from Rocker... We'll see how that works. 

I would sand to 400-600, buff with a mild abrasive such as tripoli and/or white rouge then polish with a hard wax.  If this sounds like the Beall buffing system, it is.

I would sand to 400-600, buff with a mild abrasive such as tripoli and/or white rouge then polish with a hard wax.  If this sounds like the Beall buffing system, it is.

I'd do that but skip the wax. Cocobolo is so naturally oily that you often don't need it if you do a fine buff.

 

EDIT: hm ... that's odd. I'm logged in as me but the posting avatar says "guests"

EDIT: hm ... that's odd. I'm logged in as me but the posting avatar says "guests"

 

You're posting correctly, just refresh your screen and you'll see it's really you..

You're posting correctly, just refresh your screen and you'll see it's really you..

Ah. So I do. .Thanks.

  • 1 month later...
  • Author

So I'm finally getting around to doing this. Did a coat of dewaxed shellac, sanded lightly, then put the arm-r-seal on top. Nice glossy finish, just that after 24 hours (in my house at 68 degrees) of drying, it is still tacky. I figured with a shellac sealer, no oils from the cocobolo should be affecting the poly finish.

Any ideas? Wait longer??? Heat gun to accelerate drying?

Sent from my iPhone using Tapatalk

So I'm finally getting around to doing this. Did a coat of dewaxed shellac, sanded lightly, then put the arm-r-seal on top. Nice glossy finish, just that after 24 hours (in my house at 68 degrees) of drying, it is still tacky. I figured with a shellac sealer, no oils from the cocobolo should be affecting the poly finish.

Any ideas? Wait longer??? Heat gun to accelerate drying?

Sent from my iPhone using Tapatalk

I always use 3 coats of dewaxed on cocobolo

  • Author

Sorry, I meant to write that I did two coats of shellac.

Sent from my iPhone using Tapatalk

I'd expect that two coats of a 2lb or heavier solution should have done the trick. I use 3 coats of a 1lb to 1.5lb (I don't shoot for much precision on my weighing).

  • Author

For what it's worth, I didn't cut the Zinniser shellac from the can at all... Full strength.

Sent from my iPhone using Tapatalk

For what it's worth, I didn't cut the Zinniser shellac from the can at all... Full strength.

Sent from my iPhone using Tapatalk

That's probably a 3lb cut. I make my own from dewaxed flakes

  • Author

About 10 of the 20 cured enough so I was able to get a second coat on. Other 10 are still a little tacky after a week in 65 degree temps.

I'm near the decision point to either sand lightly and do another coat of shellac before the poly again or a heat gun. Not sure if a heat gun will work though to accelerate the drying time...

Sent from my iPhone using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.