..Kev Posted May 11, 2015 Report Posted May 11, 2015 I just ran into an issue with my Grizzly 715p and wanted to put it out to Grizzly Table Saw owners in case they run into the same issue.. I have a 715p but, I've seen the same issue on a couple of 690s where the arbor is just a little over size. This obviously comes into play when changing the blades. In my case, I purchased a new dado king (Forest) and it wouldn't fit on my saw. Since I bought it at Grizzly, it allowed me to address the issue all at one place I have always had good luck with customer service at Grizzly and today was no exception. They brought out several Dado Kings, opened them all, and measured the hole on each of them. They found me one were the hole was a couple thousands over. That combined with a very light sanding of my arbor (in case there was a small burr) fixed my issue. When I say light, we're talking about enough to remove the paint and that's about it. I also went ahead and measured my (Forest) Woodworker II and found it to be another couple thousands larger than the new dado stack. Good luck! Hope this helps someone else! 2 Quote
RichardA Posted May 11, 2015 Report Posted May 11, 2015 I just ran into an issue with my Grizzly 715p and wanted to put it out to Grizzly Table Saw owners in case they run into the same issue.. I have a 715p but, I've seen the same issue on a couple of 690s where the arbor is just a little over size. This obviously comes into play when changing the blades. In my case, I purchased a new dado king (Forest) and it wouldn't fit on my saw. Since I bought it at Grizzly, it allowed me to address the issue all at one place I have always had good luck with customer service at Grizzly and today was no exception. They brought out several Dado Kings, opened them all, and measured the hole on each of them. They found me one were the hole was a couple thousands over. That combined with a very light sanding of my arbor (in case there was a small burr) fixed my issue. When I say light, we're talking about enough to remove the paint and that's about it. I also went ahead and measured my (Forest) Woodworker II and found it to be another couple thousands larger than the new dado stack. Good luck! Hope this helps someone else! Thanks Kev, my Doctor just bought a 715 and he hasn't set it up yet, I'll let him know what, who, and how to deal with the problem should it arise for him! Again, Thanks. Quote
Tpt life Posted May 11, 2015 Report Posted May 11, 2015 Hey Kev, did you put a mic on your arbor and grab a measurement? Was it a few thou over published spec? Quote
..Kev Posted May 11, 2015 Author Report Posted May 11, 2015 I didn't mic my arbor C. I did test the dado stack that wouldn't fit my saw on the show room saw at Grizzly and it did fit that one. There just seems to be some inconsistency from saw to saw. Quote
Brendon_t Posted May 12, 2015 Report Posted May 12, 2015 That is quite strange. I would definitely mic the arbor and compare to spec. It's good that you found a stack that will work but what about in the future. Xyz company comes out with saw blade of the Millennium but it won't fit your arbor. I would be curious if my arbor was over or blades under. Quote
dwacker Posted May 12, 2015 Report Posted May 12, 2015 I would check the arbor run out. If its the slightest bit OOR the blade wont fit and it will destroy bearings. Quote
..Kev Posted May 12, 2015 Author Report Posted May 12, 2015 I checked the arbor and it's not OOR.. With the light sanding I did, I'm not sure what it was when I started. Although the arbor was certainly part of the issue, the blade was the other part. The arbor hole in the blade was a a few thou under so, it was a combination of the two. Quote
Brendon_t Posted May 12, 2015 Report Posted May 12, 2015 Good to hear, when that 10" laser beam blade comes out, it should fit Quote
..Kev Posted May 12, 2015 Author Report Posted May 12, 2015 Good to hear, when that 10" laser beam blade comes out, it should fit For sure! In the end, I was just trying to save someone else the same leg work to correct the issue.. Quote
ChrisG-Canada Posted May 12, 2015 Report Posted May 12, 2015 Good to hear, when that 10" laser beam blade comes out, it should fit I use my lightsaber... but only for rough dimensioning Quote
Brendon_t Posted May 12, 2015 Report Posted May 12, 2015 I use my lightsaber... but only for rough dimensioning 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.