Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Grain Filler Question

Featured Replies

I will be finishing a QSWO top with the Faux Stickley/Jeff Jewitt method.  I want to make sure the natural wood's figure, grain, etc comes through.  I was also thinking of using a wood grain filler.  Is this a bad idea?  Or does that stuff only seal the pores?

  • Author

I was looking at those.  That finishing schedule is pretty particular so I guess the answer I hate: "try it," will be in order.  :)

  • Author

Jeff's schedule is a trans-tint (water based) stain, followed by General Finishes SealACell Sealer, followed by a stain gel followed by ArmRSeal (satin).  I am not sure if the SealACell is a grain filler but the manufacturer calls it a wood sealer.  And .. re-reading his notes I get my answer:

One of the qualities that make quarter sawn white oak attractive is its distinctive pore structure. By emphasizing these pores with a dark glaze, the true Mission effect is achieved. Use the gel stain as noted in the instructions for each sample.

So ... no grain filler I guess.

Edited by Lee Bussy
Clarification

I use thixotropic pore filler on furniture and guitars. The wood grain is not obscured using this stuff. You wipe it on with the grain, wait a while, then wipe across the grain to prevent it from being pulled out to remove any excess. Wait 12 hours and you are then good to apply finish.

The last job I used this on were nightstands made from sapele which is open pored like mahogany. I then applied Seal A Cell and top coated with Arm A Seal. It is like a babies butt now with no micro holes or pore sinkage. After applying the finish the light reflection from the grain of the wood alters as you view from different angles. It looks stunning.

 

OP what wood are you using as some don't need pore sealing?

  • Author

Thanks Terry.  can you recommend a brand?  (And hopefully that brand will be available in the US).  

Lee I use Jecofil made by W.S. Jenkins and Co Limited in England.

http://www.jpennyltd.co.uk/shopping/pgm-more_information.php?id=142

I have had a look at the likely suspects Woodcraft and Rockler for something similar but can't see anything. There may be other specialty USA based websites that may be able to either supply the excellent Jecofil or a US manufactured thixotropic pore filler. If you can get it you will use it all the time.

Rustins also make a similar product so if that is obtainable in the US try that. It's not as good as Jecofil but it is certainly good.

There is one alternative of course in the absence of a proprietry pore sealer and that is shellac in a thin cut (1# maybe). It's a little more work as you may have to coat it a couple of times to fill the pores lightly sanding between coats. I've done a few guitars that needed their mahogany necks filling with shellac and it is very sucessful.

  • Author

I got a note back from Jeff Jewitt on this as well.  He says the combination of SealACell and ArmRSeal will close all that up - and recommended not to use a grain filler.  

I guess since I went to the trouble of buying his book, watching his DVD, and reading his documents, I should trust him?  :P

This will be a satin finish anyway so not quite like your guitars.  I will file that away for future reference though so thank you!

 

I would not use a grain filler. Here is my QSWO finish schedule which is very similar to what's you're doing:

1. Water based dye
2. Dewaxed blonde shellac
3. Oil based stain
4. Topcoat of choice (Waterlox for most projects)

Water based dye doesn't work into oak pores very well. Shellac seals the dye and the oil based stain works into the pores and tones on the shellac. 

  • Author

Water based dye doesn't work into oak pores very well. Shellac seals the dye and the oil based stain works into the pores and tones on the shellac. 

That's pretty much spot-on to what Jeff said about the pores.

That is some REALLY pretty figuring/flecks you have in that table!  Did you end up getting the QSWO around here?  Because I drew a big fat bust in KC looking for it.I would have driven up there in a second to be able to sort through a pile.

I get all my QSWO from a guy in Glenwood Iowa. He cuts all his red and white oak all rift/quartered and usually thick for 4/4. I think he mainly mills swamp white oak which is a pleasure to work with. For the oil stain I've had good luck with Varathane from Menards. I work it into the pores good then wipe off pretty hard to popup the rays. This finish schedule is a lot of steps but gives a look that stain and poly alone just doesn't do. 

Make sure you practice on test boards.

  • Author

Pschfft ... practice ... that's for people who want to know how it will turn out!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.