Recommended Posts

Posted

Apologies in advance as it's probably been answered before.

I have a Bosch sliding compound mitre saw (with a Bosch higher quality blade), a handheld corded Bosch circular saw (with the stock factory blade which insists on throwing chips in my face), and a Makita 18V circular saw (with a Freud Diablo blade). All of these are coming to their end of life so want to do an upgrade.

Are Forrest blades worth the extra cash? I was thinking of a crosscut blade for the mitre saw (...), a rip blade for the Bosch circular, and a good combo blade for the little Makita.

In addition, I have a bandsaw with the Chinese (yes, I know, beggars can't be choosers) factory blade on. I'm getting OK results but only because I spent a long time tuning it up. I was thinking the Wood Slicer 1/2" is a no-brainer.

Posted

I use a forrest blade on my table saw, it's pretty good, but the real question is what level of finish do you need from these cuts? Are you going straight to glue, or are these rough cuts? If they are rough cuts then you certainly do not need a forrest blade if they are going to glue then you may want one. However, I would still be more inclined to go to a Diablo blade for the circular saws certainly rather than spending extra money.  The difference in price is enough to buy a new tool, and not necessarily a cheap one. 

Posted

==>Are Forrest blades worth the extra cash?

Depends on what you're doing and your expectations...

I've got several brands of SCMS blades. By far, the Forrest Signature is the best... But it's expensive to purchase ($175) and expensive to resharpen ($45 -- the sides of the cutters are taper-ground and more setup is required at the sharpening station). But, the blade is designed to leave absolutely clean cuts on crown moldings -- which is no easy accomplishment... The cut is just about on-par with a TS sled and high-end xCut blade...

If you do high-end trim, it's probably worth it... But for most furniture applications, the SCMS get's you close and the TS sled is the final cut...

Posted

Forrest blades are excellent.  Whether or not they're worth the extra cash is subjective, and depends in part on what the end cost actually is.  I used to think they were worth a premium, but after trying 70 or so blades that include the vast majority of top shelf brands, I now think you can buy a blade of the same caliber for less money.  You can get what you pay for if the price is right, but once you get much beyond the $100 mark, I think someone else is getting what you paid for!  

IMO blades from Ridge Carbide, Infinity, the Tenryu Gold series, Freud Premier series, and others are of comparable quality with comparably sized carbide.  Their 40T general purpose blades sell frequently in the $90-$100 range...sometimes less.  How good any particular blade is depends a great deal on how well suited it is for the given task.  No brand has impressed me more than Infinity so far....their 60T 010-060 - < $70 (similar to the WWI) or 010-080 Ultrasmooth - < $80 (similar to the Duraline) are excellent crosscut blades....if your Bosch is 12" look to the Infinity 012-090.  

For circular saws some of the Freud blades are tough to beat for the price.  LU79R007, D0760x, D0740x, D0640X, etc.  

 

 

 

  • Like 1
Posted

Thank you all, saved some money I think. I've ordered knottscott's recommendation of the Infinity 012-090, and a new diablo blade for the 2 circular saws. Less than half price of Forrest.

Posted

I don't own a 12 inch saw, so haven't tried that specific blade, but I can say that the 5 ten inch Infinity blades and the 8 inch dado I've used have all looked and performed like world class blades.  Let us know how it works out.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 39 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined