Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Tip #4 – Diamonds are a Cutter’s Best Friend!

Featured Replies

  • Popular Post

This was planned as a future tip, but some posts on Shelix heads have surfaced, so this week, two tips...

For those with Byrd Shelix heads... Actually, this tip is probably applicable to any segmented head, but I’ve only got working experience with the Byrd product...

Numerous talking heads (read as those with paid sponserships) will proclaim, “Get a new edge in seconds” by rotating the cutter... Anyone actually try that??? And what went wrong???

To do the job properly, you need to remove the cutters from the head, soak them in bit/blade cleaner (an ultrasonic bath is best), take a brass-bristle brush to the cutter beds, then reinstall the cutters using 5Nm of torque... Ge’ezzzzzzz, maybe knives aren’t such a pain in the ass after all???  Note: why do you need to do this??? Well, ANY crud/dirt/pitch/etc between the base of the cutter and the cutter bed will result in a poor stock surface (trenches), a chipped/cracked cutter, and/or both... Again, my experience is with the Byrd product, YMMV...

So what’s the tip??

Since all the cutters are removed from the head, how do you know which edge to align when re-installing??? Some will claim they can identify the edge using a magnifier – and they’d be wrong (about 50% of the time)... You see, under normal use, the cutting edge gets nicked (as you’d expect) AND the opposite edge gets nicked (which you wouldn’t), but remains sharp – interesting, isn’t it? The Shelix principal is the sheared cut PLUS every spot gets hit by two or three cutters (depending on a bunch of factors that I won’t get into)...

So what’s the tip??

Before removing the cutters from the head, mark the side in use with a diamond scribe... Over time, all four edges will get marked, and it’s time to toss the cutter... Here’s the least expensive diamond scribe that I can actually recommend: http://www.tedpella.com/tools_html/54410.htm#_54463

But wait a minute, “I read on the internet (so it must be true) that you can just use a sharpie...” Yea, it’s funny how many recommend that one – especially since they’ve never actually tried it... But that’s just life on the internet, “Nobody knows you’re a dog...”

But I can hear some say, “Each edge of the cutter is numbered (or marked in some way), so I just keep them all the same...” In normal use, cutters get chipped, crack, shatter, etc – so they don’t all get replaced at the same time... Over time, the numbering (marking) sequence falls off... You need a way to mark the used edges...

 

Keep those edges sharp...

17 minutes ago, hhh said:

 “Nobody knows you’re a dog...”

Is this tip #5? :) 

One question:  what is an ultrasonic bath?

Edit:  ok, I googled it and wikipedia explained.  I had never heard of this.  Seems like it would be useful for a whole bunch of things.  Do you use this for your table saw blades too?  Router bits, etc.?  Basically anything carbide tipped?

https://en.wikipedia.org/wiki/Ultrasonic_cleaning

  • Author

==>Is this tip #5? :) 

Tip #5 – Have a Moxon, get an Oilstone...

We'll just let the suspense build... :)

40 minutes ago, bgreenb said:

One question:  what is an ultrasonic bath?

Edit:  ok, I googled it and wikipedia explained.  I had never heard of this.  Seems like it would be useful for a whole bunch of things.  Do you use this for your table saw blades too?  Router bits, etc.?  Basically anything carbide tipped?

https://en.wikipedia.org/wiki/Ultrasonic_cleaning

We use an ultrasonic cleaner with (TSP) Trisodium Phosphate at work to clean copper fittings to be used in medical gas systems. I never thought to clean my saw blade in it, but now I have a reason to borrow another tool.

You know that the Byrd cutters have numbers in each corner right? You can reference by that. I have a google spreadsheet that has which cutter edges are used. 

Trip's Tips...I like this one.  I haven't had to mess with my cutters yet but I've wondered about this very thing.  We need to rename Trip's Tips to Trip's Rips, as in Trip Rips my wallet a new @$$hole...every Trip's Tips seems to cost me money.  Is there a reason any of these are no good?...

http://www.amazon.com/gp/product/B0058ECW6S?keywords=diamond%20scribe&qid=1452525507&ref_=sr_1_3&sr=8-3

http://www.amazon.com/gp/product/B004YK66NM?keywords=diamond%20scribe&qid=1452525507&ref_=sr_1_2&sr=8-2

http://www.amazon.com/Techni-Tool-Scriber-Diamond-Retractable-Anodized/dp/B000PDLDKS/ref=pd_sim_sbs_328_2?ie=UTF8&dpID=118nXo%2B4QvL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=00TGPDAXZ0ME1RH6K7XK

 

 

  • Author

==>in a dremel

Before I thought of a diamond scribe, I was tempted to try my Dremel... But I figured the wheel would skip a bit and might damage the adjacent edge... And, quite frankly, a scribe is much faster with less risk of something going wrong... At $25, not much of a downside...

 

==>Do you use this for your table saw blades too?  Router bits, etc.?  Basically anything carbide tipped?

Yes and no... You've got to be a bit careful here... Maybe I should turn this into a tip.. :)  I learned this from Forrest many moons ago -- I got my blades back so shiny they were like new -- I just had to ask how they did it (I'm that kind of guy -- if I've got a question, I just pick up the phone)... Before resharpening blades, Forrest puts them in an ultrasonic bath... From then on, I was hooked...

One very important caveat: I typically purchase top-shelf tooling, so the brazing is of high-quality and will stand-up to ultrasonic baths... Put something from HF in an ultrasonic bath and you'll degrade the brazing with the risk of the tool flying apart when next used...

So yes, if the tooling has burned-on pitch, it goes in the bath... Large items so to my auto repair guy...

 

==>You know that the Byrd cutters have numbers in each corner right? You can reference by that. I have a google spreadsheet that has which cutter edges are used. 

From above post...

But I can hear some say, “Each edge of the cutter is numbered (or marked in some way), so I just keep them all the same...” In normal use, cutters get chipped, crack, shatter, etc – so they don’t all get replaced at the same time... Over time, the numbering (marking) sequence falls off... You need a way to mark the used edges...

And BTW: not all genuine Byrd cutters are marked in every corner... :)

I've personally received some marked with the company logo, some market BT and one set with numbers...

Trust me, you can start with a spreadsheet, but you will chip some cutters over time... I'm convinced that marking edges is best practice...

 

==>Is there a reason any of these are no good?

Don't know... I try to only recommend things I actually have hands-on experience with... On the internet, nobody knows you're a dog...  Not to date myself, but I remember when the original cartoon appeared in the New Yorker... My mother didn't get it, so she handed me the magazine and asked for an explanation... :) To this day, I'm not sure she has mastered eMail... Sad...

 

49 minutes ago, hhh said:

so she handed me the magazine and asked for an explanation..

I'd have thought by now your mother would have learned to avoid this. Unless she carved out a few hours of her day just for this. :P

Kidding of course...You're so thourogh and amazingly informative.

On a side note- If you can't afford or think it's cost prohibitive to invest in an ultrasonic cleaner. You can use TSP in a plastic 5 gallon pail and agitate ocasionally. You won't get the same results in as short a time, but it still works. Atleast that is my experience with copper plumbing fittings.

  • Author

==>Trip's Tips seems to cost me money

Well, the next one has an implied spend -- sorry...

I could sort through them (I've got about twenty in the hopper) and just post the 'no spend' tips... :)

#6 involves Modeler's Rasps, but I believe you may already have one or two...

Hummm. Let me work on it...

2 hours ago, Tom Cancelleri said:

You know that the Byrd cutters have numbers in each corner right? You can reference by that. I have a google spreadsheet that has which cutter edges are used. 

Sounds like as long as you never take more than one out at a time it is OK.  But it you were removing a few and batch cleaning them all at once, you could get them mixed up.

1 hour ago, hhh said:

==>in a dremel

Before I thought of a diamond scribe, I was tempted to try my Dremel... But I figured the wheel would skip a bit and might damage the adjacent edge... And, quite frankly, a scribe is much faster with less risk of something going wrong... At $25, not much of a downside...

 

I was just thinking of a mark that you can see more easily than a few light scratches.  A lot of moderate scratches strikes me as more visible,

  • Author

==>I was just thinking of a mark that you can see more easily than a few light scratches.  A lot of moderate scratches strikes me as more visible,

With clean cutters and decent lighting, it's not too bad... Obviously, with a Dremel, it would be more straight forward... So you're right there. My thoughts were on solid carbide is quite hard, so I was just worried about marking just the intended edge and not bounce around and also mark an unintended edge, or worse, score an edge...

But it's a tip... I try to offer only what I've used... Someday, I'll try a Dremel and post another tip.. :)

 

1 hour ago, hhh said:

==>I was just thinking of a mark that you can see more easily than a few light scratches.  A lot of moderate scratches strikes me as more visible,

With clean cutters and decent lighting, it's not too bad... Obviously, with a Dremel, it would be more straight forward... So you're right there. My thoughts were on solid carbide is quite hard, so I was just worried about marking just the intended edge and not bounce around and also mark an unintended edge, or worse, score an edge...

But it's a tip... I try to offer only what I've used... Someday, I'll try a Dremel and post another tip.. :)

 

For sharpening carbide cutters for the lathe and work the pedestal grinder isn't bad.  The main issue I would see would be holding the cutter.  But it shouldn't grab and jump around.  And it would not work well at all with a silicon oxide wheel.  But Silicon Carbide wheels are readily available and tend to come in the dremel sets.  And putting light marks wouldn't use them up fast.

 

It also makes neat green sparks.

  • Author

==>It also makes neat green sparks.

Ohhh, why didn't you say so... Green... Mummmmmm... Green... :)

OK, I cave... I'll give it a whirl and compare...

BTW: do green sparks cost more? :)

Regarding the ultrasonic cleaner, I bought this one: http://smile.amazon.com/gp/product/B001DKDAVW?psc=1&redirect=true&ref_=oh_aui_search_detailpage

It's original purpose was to clean the wife's jewelry, which it does very well. I've tried the specific jewelry cleaning liquid, but find that warm soapy water works just as well. I've used it to clean drill bits, greasy screws, router bits. You will need a bigger, more professional one if you want to clean saw blades.

DISCLAIMER: Don't use it to clean your watch even though it says you can. I cleaned my Chopard in it and the rotor that winds the watch movement loosened. Repair was not cheap.

DISCLAIMER 2 (more important if you intend to stay married): When you clean rings with stones (read diamonds), there is a chance the stone will fall out. I think this is a good thing because it means a weak point in the setting of the stone was exposed and a good jeweler can fix it. So, when you remove ring, check for any important parts that may have fallen out. Easy to retrieve - your marriage may be dependent on actually doing so before you discard the water :blink:

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.