Lee Bussy Posted January 24, 2016 Report Posted January 24, 2016 I have a Rigid 4510 which in all other ways is a fantastic beginner saw for a guy with limited space. My problem is with rips where the limited fence size is causing me to get some craptasticly curved cuts. I know I can replace whole fence setup with a bessy style system but that's but a little expensive right now and a little bit of overkill. I thought clamping a (insert something here) would be a good way to go. The "something" is where I am stuck. I'd like to find something inexpensive, straight without me having to be the arbiter of what's "straight." Something I can just find online (preferable) or local to purchase and just get back to work. I was thinking of something like an aluminum extrusion but there are so many different types, I don't know where to start. The fence extrusion portion is 25-1/2 inches long, 2" wide x 2-1/2" high. Here's what we are working with, any ideas what I can buy and just clamp on with say a pair of fence clamps? 1 Quote
knotscott Posted January 24, 2016 Report Posted January 24, 2016 In addition to being cost prohibitive, I'd think you'd struggle with the weight and size of a fence like a Biesemeyer on a portable jobsite saw. Pretty sure the fence would outweigh the saw, and the fence would hang off the end a long way. It shouldn't be too hard to come up with some sort of auxiliary fence that you can customize to suit your needs. The clamps you linked are one method of hold an aux face in place, but you could attach it to the t-slots as opposed to using clamps. There are many ways of building and attaching a housing over the fence too. 2 Quote
wtnhighlander Posted January 24, 2016 Report Posted January 24, 2016 Lee, do I understand correctly, it is the length of the fence (or lack of) that gives you problems? If so, knotscott is correct about the auxilliary fence options, although having good outfeed support under the stock is just as important. If your fence isn't square to the blade, or moves under pressure, that's a different problem, and should be corrected before worrying about adding length. The fence on that saw appears to lock down fore and aft, so it shouldn't move during a cut, unless the rear locking clamp is loose. The extrusion appears pretty solid, so flex shouldn't be an issue. The T end isn't very wide, so I can see where keeping it parallel to the blade might be difficult. There are usually a couple of nylon pads under the T, which serve to help it slide along the rail. If one of those is loose or missing, the clamping pressure will be uneven, and it won't be square. 1 Quote
Lee Bussy Posted January 24, 2016 Author Report Posted January 24, 2016 25 minutes ago, knotscott said: In addition to be cost prohibitive, I'd think you'd struggle with the weight and size of a fence like a Biesemeyer on a portable jobsite saw. Pretty sure the fence would outweigh the saw. No doubt. As much as I like this saw, it's crazy to dress it up to that extent. The upside to that would be the fence could be used on my next saw if/when I get one. 27 minutes ago, knotscott said: It shouldn't be too hard to come up with some sort of auxiliary fence that you can customize to suit your needs. The clamps you linked are one method of hold an aux face in place, but you could attach it to the t-slots as opposed to using clamps. There are many ways of building and attaching a housing over the fence too. I was hoping to find a manufactured item that would serve so I don't have to build ... I would have to go back to the guild and spend time there working, then bring it home and try it out. This may sound lazy but it's really just about optimizing my time. The best price I have found on extruded aluminum is about $75 for a 48" stick. Higher than I thought it was. 1 hour ago, wtnhighlander said: Lee, do I understand correctly, it is the length of the fence (or lack of) that gives you problems? The length. 1 hour ago, wtnhighlander said: If so, knotscott is correct about the auxilliary fence options, although having good outfeed support under the stock is just as important. I do have an outfeed table, and I am going to "skirt" the table itself to increase the size of the table proper. 1 hour ago, wtnhighlander said: If your fence isn't square to the blade, or moves under pressure, that's a different problem, and should be corrected before worrying about adding length. The fence on that saw appears to lock down fore and aft, so it shouldn't move during a cut, unless the rear locking clamp is loose. The extrusion appears pretty solid, so flex shouldn't be an issue. The T end isn't very wide, so I can see where keeping it parallel to the blade might be difficult. There are usually a couple of nylon pads under the T, which serve to help it slide along the rail. If one of those is loose or missing, the clamping pressure will be uneven, and it won't be square. I don't think it's moving. As you say it clamps fore and aft and seems to do a great job of it. I also do check the spacing at the front and back of the blade - and I have done the same from the miter slots. It's a pretty consistent clamping action.25" of fence when you are ripping 8" sheets is just not enough. Quote
knotscott Posted January 24, 2016 Report Posted January 24, 2016 6 minutes ago, Lee Bussy said: I was hoping to find a manufactured item that would serve so I don't have to build ... I would have to go back to the guild and spend time there working, then bring it home and try it out. This may sound lazy but it's really just about optimizing my time.... That fence isn't overly cumbersome....maybe you could bring it with you to the guild. (just sort of thinking out loud here!...) Quote
Lee Bussy Posted January 24, 2016 Author Report Posted January 24, 2016 13 minutes ago, knotscott said: That fence isn't overly cumbersome....maybe you could bring it with you to the guild. (just sort of thinking out loud here!...) That's a good idea. Still need to find the time to do that. Quote
Brendon_t Posted January 24, 2016 Report Posted January 24, 2016 Could you not just replace the aluminium rail with an aluminum extrusion? It may not be drop in ready but some hip pocket engineering and I'm sure you could get it mounted and solid. Quote
Lee Bussy Posted January 24, 2016 Author Report Posted January 24, 2016 If it only clamped in one place then probably. It clamps on the front and the back however, I'm not sure how I would pull that off and still have a clam up there. Quote
Brendon_t Posted January 24, 2016 Report Posted January 24, 2016 The extrusion has a rail to receive accessories on the bottom as well. It looks like you could slot the bottom and insert that front clamping arm. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.