Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Options for filling in some defects in panels.

Featured Replies

I'm building a small cover for our door chimes and found a piece of oak with some great figure which I'm going to use for the panel. Cutting out the slices for the panels, they all have a few defects (small voids). I know I won't be able to remove them completely, but I'd be interested in hearing about any suggestions there may be out there.

12e013576864e2e4d71c33e7ac583f93.jpg

Thanks.

Sent from my iPhone using Tapatalk

  • Author

I don't think I'll be able to really disguise them. I'm thinking of using some epoxy just to level out the voids. Tinting it or not is another question.

Sent from my iPhone using Tapatalk

I think epoxy is your best bet i don't know if i personally would want to fill them. It'd ruin part of the charm of that board.

  • Author

This actually started out as a chunk of firewood. I managed to slice out about 10 blanks from it but the two shown here are the best of the lot. I'm going to try some clear epoxy on a test piece and see how it looks. Since the void will be covered with epoxy, should I put some finish in the void first? (I know, more experimentation will give me the answer, just trying to get a head start with some feedback from more experienced members of the forum. )

Sent from my iPhone using Tapatalk

Be diligent in taping around the void and only getting epoxy where you want it.  Epoxy will seep into blonde woods leaving a color change even after leveling it off.

given where you are installing the wood, another option is just to leave the voids and put a thin layer of black material behind it so that no light shines through (One suggestion would be to glue black paper to the inside of the box)

Really just depends on the look you are going for

  • Author

The voids do not go through the panel. The panel itself is about 1/4" thick. But due to the nature of the wood, planing it to get rid of the voids is not an option. It started out as a chunk of firewood that I pulled out of the pile years ago, so it's nice and dry but has some checking on the edges. I'll stabilize the edges with either CA or epoxy before I route the rabbets for the rails.

Sent from my iPhone using Tapatalk

you could add some saw dust to the epoxy mix to get a similar color match.

  • Author

I probably will just use Arm-R-seal on it. Haven't thought about that too much but I do want to accentuate the curl in the wood.

Sent from my iPad using Tapatalk

I did the trans tinted shellac on a piece of oak that had some curl in it. I thought it worked pretty well Marc did a video on making wavy grain pop, i did essentially the same thing. Left side towards the top. Wish i could get more oak like that.

12654317_10100920842067249_8566545001505

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.