Cygnus A Posted July 11, 2016 Report Posted July 11, 2016 First the pictures:http://imgur.com/a/ERqyc The Saw I am fairly new to woodworking and had a Grizzly G0715P saw that I purchased last fall. I had problems with it for 6 months before finally sending it back. It had gotten so bad that I had stopped even trying to make things for a month, and spent 4 weekends trying to align the blade only to find alignment would shift any time I raised or lowered the blade. I had read that this model had this issue a few years ago and Grizzly claimed they had corrected it, but obviously not. I decided to go all in with a 3HP PCS Sawstop and couldn't be happier. The difference between the Grizzly and Sawstop is ridiculous (in price and quality!). The precision I am getting now is so much better and I am actually having fun cutting wood instead of feeling like I am fighting the machine. I do not have 240v in the garage (and I am renting, so I couldn't add an outlet), but I did happen to have an unused 240v outlet in the laundry room. So I build an extension box that plugs into the outlet and runs 25 feed into the garage. The box splits the wiring so I have dual 240v outlets and dual 120v outlets. Outfeed Table Initially I was going to make a Paulk style bench, but since I didn't need it to be mobile, I wanted something more robust. So I stole and merged various ideas around the internet and added my own engineering into it. I like how it turned out. I had started building the outfeed table to match the Grizzly so it is a little short compared to the 52" Sawstop. Top surface: * 3/4 ply * 3/4 MDF * 3/16 hardboard * 1x4 poplar The ply and MDF are screwed together in a 6x6" grid. I didn't want to glue so it could be disassembled later, if necessary. The hardboard floats inside of the poplar trim so it can easily be replaced later. The poplar trim has an additional 3/4 ply backing so the total thickness of the ply/mdf at the table edge is 2.25". This will give me a solid surface to add clamps to later (face clamp/tail clamp). The frame is all 3/4 ply with a 1/2 ply shelf. I used adjustable feet to level it flush with the saw. Crosscut Sled Not much to say here, but this one is far superior to my previous one. I followed William Ng's tutorial and the result is perfect 90 degree cuts. I chose to use MDF as the sled base for stability since I had some warpage problems on my previous plywood sled. Let me know what you think. I am going to post a Sketchup model of the table once it is complete. This will help me learn the software and hopefully help other out with my outfeed table design. 2 Quote
JosephThomas Posted July 11, 2016 Report Posted July 11, 2016 Looks good. is the hardboard on top tacked down with finish nails or hot glue or anything? or is it realy just resting there? I have a layer of hardboard on top of mine and i opted for small screws ever 12" or so....it does an ok job but I was more worried about driving the screwed the perfect amount, too easy to drive all the way through. I think next time I will use hot glue so I can remove it easily (and a couple small brads to help while the glue dries). Quote
Cygnus A Posted July 11, 2016 Author Report Posted July 11, 2016 10 minutes ago, JosephThomas said: Looks good. is the hardboard on top tacked down with finish nails or hot glue or anything? or is it realy just resting there? I have a layer of hardboard on top of mine and i opted for small screws ever 12" or so....it does an ok job but I was more worried about driving the screwed the perfect amount, too easy to drive all the way through. I think next time I will use hot glue so I can remove it easily (and a couple small brads to help while the glue dries). The poplar trim keeps the hardboard in place. It is a snug fit and does not move. I can pry it out with a flat screwdriver if needed. Quote
Chet Posted July 11, 2016 Report Posted July 11, 2016 Looks like a nice setup, you should be real happy with that. Quote
JosephThomas Posted July 11, 2016 Report Posted July 11, 2016 The poplar trim keeps the hardboard in place. It is a snug fit and does not move. I can pry it out with a flat screwdriver if needed. Huh, id expect it to curl up with time... You probably have better climate control in your garage than me I guess... Sent from my Nexus 5 using Tapatalk Quote
Cygnus A Posted July 11, 2016 Author Report Posted July 11, 2016 8 minutes ago, JosephThomas said: Huh, id expect it to curl up with time... You probably have better climate control in your garage than me I guess... Sent from my Nexus 5 using Tapatalk Well, it is only a week old. So maybe it will, but I live in the desert so moisture shouldn't be an issue. Quote
Chet Posted July 11, 2016 Report Posted July 11, 2016 I used to have a bench that had a hardboard top that got changed all the time. I just used some small brads to hold it down, no glue and it popped off real easy when the time came. I would get tiny high spots around the brads when I put them in but they would sand flat in an instant. I am guessing that the high spots where an expansion of the hardboard when the brad went in because of the make up of the hardboard itself. Quote
Chestnut Posted July 12, 2016 Report Posted July 12, 2016 That's a real nice setup you've got there. That outfeed table defiantly looks like it's made well and is going to last. It's really unfortunate that you had so much trouble with the grizzly but at least it lead you to a saw that you may never need to replace or upgrade. What did you use for leveling feet on the outfeed table? Quote
Alan G Posted July 12, 2016 Report Posted July 12, 2016 Being a renter is tough to setup shop as there is only so much you can change. Looks like you made the most of it and your setup looks great! Quote
gee-dub Posted July 12, 2016 Report Posted July 12, 2016 Had a floating hardboard topped work table as you describe. Treated it with BLO and abused it for years. Dad is still using it with the original "replaceable" top. Quote
jplemons Posted July 12, 2016 Report Posted July 12, 2016 This is great inspiration for me, thanks for posting. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.