Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Forstner 16 Piece Bit Set Item #147067 WoodRiver

Featured Replies

It doesn't say whether they're high speed steel or carbon steel, but I wouldn't bother if they're carbon steel. The instant they overheat, they are ruined. Although saw tooth bits are less prone to heating than Forstner bits (those are actually saw tooth, not Forstner bits.)

  • Author

Thanks for the comment about the HSS and carbon steel. I guess I will call them tomorrow and ask. If they are HSS, is that a decent price or is this more of a junker set? I'm new to these types of bits. 

First, it is true these are not true forstners (true forstners have no brad point and a smooth cutting edge) the real forstners are rare now and most every manufacturer that makes the various bits that perform the same function call the ferstners.

 

Second, this is going to be a lower end set, the bets forstners are going to run slightly below or way above that sets price for a single bit.

That said sets like these generally are decent when the finish of the holes isn't critical.  I have one of these sets I use for less demanding work and I want to "save" my good ones.  I am reluctant to say it is the exact same bits since it was a bigger set and with these Asian bits it is hard to know if they quality is the same over years or even if they were made in the same factory.  

In the end I expect they would be a good starter set, the 24pc set I bought 6-7 years ago are reasonable for what I paid for them.  

I have a similar set from Rockler. I run them at the lowest speed my drill press has and clear the shavings often or continuously with a vac nozzle set up if I am drilling multiple holes. You do have to watch out for overheating them. 

These are softer carbon steel.  I ran a similar set for years in the 1/4" to 1" range.  They were cheap and very serviceable if you learn to sharpen them (I got quite good at it).  I have since moved on to HSS Forstners but also have the set wdwerker mentions.  It was on sale at Rockler for $24.99 and I couldn't pass it up.  I have used a few bits from it for material I consider potentially hazardous to my better bits so they were well worth the $24.99.  They may be worth double that since I have single Forstner bits that cost as much as the whole set and didn't have to risk them. 

If you need a wide range of bits right now and accept that they will get replaced later on I would go for it. If you have specific needs only right now I would buy quality bits for your task at hand and fill out your set as you go along.  I bought a 1/4" through 1" HSS set in 16ths and put everything else on my "wish list".  This is not the most economical way to acquire a set but, since other folks wanted to know what to get me as a gift and a single bit wasn't too much $$$ for any one person . . .  over a couple of years I ended up here . . .

 

Forstner Index (4).JPG

Its a good feeling to need a 2-3/16" flat bottomed, angled hole and be able to say "I've got just what I need for that right here". :)

I've got the 8 piece set of those from woodcraft, paid like $25 or something like that on sale.  They're a couple years old and haven't had any problems from them.  The larger bits went dull on me, tried sharpening them with a file like I saw online, that took forever and got crappy results.  Put a little stone(i guess) bit on my dremel, took less than a minute and got them nice and sharp again.  Obviously there are better bits out there but they're like $15-30 a piece, I'd def buy them again. 

I haven't used my (admittedly crappy Porter Cable) forstner bits since I bought these:

https://www.lowes.com/pd/WoodOwl-Brad-Point-Bit-Set/4561770

They work well in a cordless, drill too.  They're an auger type design but without a screw tip so you can use them in a press.  They clear the chips whereas a forstner bit can/will clog.

I even dropped one tip first on the concrete and it was unfazed. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.