Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Moisture Trapped Under Varnish

Featured Replies

I went to a local stain/varnish store that supplies many of the 80+ cabinet shops in this area to get what I need to finish the vanity I am building. Since I am new to finishing, I was asking him some questions about what he has and how to use it. One product he has is something (can't remember what he called it) that you use to release moisture that gets trapped below a layer of varnish. It redissolves dried varnish, allows the moisture to escape, and then the varnish redries. Many of the shops use it in the summer when high humidity causes problems.

Has anyone here heard of or used this?

Several products are out there for this.  Home remedies like vinegar and olive oil work as well (depending on the scale of the issue).  Mayonnaise, Old English, an iron, Guardsman, the list goes on.  Marc has a write up on it as well.  Of course, prevention is the best defense.

I've built plenty of pieces in summertime and I've never experienced this kind of moisture issue...if it's so humid that you can't use a normal finishing protocol, I'm apt to think it's too humid to work with wood at all because it's probably moving all over the place.  If you use kiln dried material that's acclimated to your environment, IMO you shouldn't even have a problem to deal with...with the possible exception of the nastiest bubble of a sticky low pressure system that pushes up from the Gulf the way that it does in July/August.  I'd be inclined to just stay out of the shop in that situation anyway...unless your shop is conditioned...which again would make the issue fairly moot.

Bottom line...properly dried, acclimated material and a controlled shop environment should make the whole thing a non-issue.

You didn't say...are you actually experiencing a problem or are you just expecting to have one based on something someone told you?  Sounds like he's trying to sell you a product you probably don't need.  And personally I avoid any additional finishing steps unless they're absolutely necessary...just complicates things which means more that can go wrong.

I think there is some miscommunication.   

When cabinet makers say varnish, they are usually talking about 2 part conversion varnishes that dry very quickly and, as a result, can trap moisture. lacquer and shellac, because they dry so fast, can do the same thing.  

Consumer oil varnishes like Arm R Seal take forever to dry, so they tend not to trap moisture.   

 

 

  • Author
8 minutes ago, Eric. said:

I've built plenty of pieces in summertime and I've never experienced this kind of moisture issue...if it's so humid that you can't use a normal finishing protocol, I'm apt to think it's too humid to work with wood at all because it's probably moving all over the place.  If you use kiln dried material that's acclimated to your environment, IMO you shouldn't even have a problem to deal with...with the possible exception of the nastiest bubble of a sticky low pressure system that pushes up from the Gulf the way that it does in July/August.  I'd be inclined to just stay out of the shop in that situation anyway...unless your shop is conditioned...which again would make the issue fairly moot.

Bottom line...properly dried, acclimated material and a controlled shop environment should make the whole thing a non-issue.

You didn't say...are you actually experiencing a problem or are you just expecting to have one based on something someone told you?  Sounds like he's trying to sell you a product you probably don't need.  And personally I avoid any additional finishing steps unless they're absolutely necessary...just complicates things which means more that can go wrong.

4

I don't have an air conditioner yet. I know I need one, but can't afford to buy one until I see if this shop is going to make some money.

I don't even have my spray system yet. Over the last 40 years, everything I've learned has cost me time, money, or pain; sometimes all three. Once I get my spray system, if it can go wrong, it probably will.

The guy at the spray shop is real helpful. He was just letting me know he had it if I needed it

  • Author
2 minutes ago, Mike. said:

I think there is some miscommunication.   

When cabinet makers say varnish, they are usually talking about 2 part conversion varnishes that dry very quickly and, as a result, can trap moisture. lacquer and shellac, because they dry so fast, can do the same thing.  

Consumer oil varnishes like Arm R Seal take forever to dry, so they tend not to trap moisture.

 

If my shop is going to work, I will probably be getting most of my supplies from this shop.

I don't know enough yet to even ask the right questions, but a slow drying varnish wouldn't be the best thing to use in a production shop would it?

5 minutes ago, freedhardwoods said:

If my shop is going to work, I will probably be getting most of my supplies from this shop.

I don't know enough yet to even ask the right questions, but a slow drying varnish wouldn't be the best thing to use in a production shop would it?

No.  Regular one part varnish is a horrible finish in a production environment.  It traps dust and moisture and is disgusting to spray.  

If someone is spraying "varnish", then chances are they are actually using a 2 part high solids conversion varnish, or something similar.   Those products might have polyurethane resins (like a consumer varnish) but they are catalyzed (cross linked) and use much faster drying solvents.  

 

  • Author

I remember he said something about catylized" and "precatylized".

Some shops use a "sealer", then two coats of varnish, sanding twice after the first two coats. He recommended using the two coat method that doesn't require the sealer and only having to sand once. It costs more to buy, but you more than make up for it in labor savings.

I hope I said that right.

I use 2 coats of sanding sealer , sand , then one or 2 coats of precat finish. Both are waterbourne. Fire Marshall and neighbors in the commercial building bitching about the smell is why I switched to waterbourne finishes 20 years ago.

Waterbourne finishes don't care if it's hot and humid, they just dry a little slower.  They don't do well below 55 degrees .

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.