Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Shades or Diffusers for regular bare bulbs

Featured Replies

So, part of my lighting solution is a set of regular porcelain lamp holders. I like having these as my ceilings are a little low, and they throw light out sideways better than my shop-lights or track-lights.

socketwithpullchain.jpg

The issue is I end up looking directly at them more than is pleasant. Has anyone found a cheap or easy solution? For awhile I was thinking of china globes, but all the ones I could find were intended for pendants rather than direct ceiling mount. The bulbs are LED, so I'm not worried about a fire hazard.

Have you looked at any of those slim line LED fixtures that almost look like recessed lights? They are only about  1/2" thick & range in size from about 5" - 15" in diameter. Harder to break & much less glare. More money though.

  • Author
On 5/12/2017 at 3:54 PM, wtnhighlander said:

Wide-mouth Mason jars. Attatch the ring to the ceiling around the fixture, lightly spray the inside of the jar with white paint. Screw jar onto ring, ove the bulb.

Cool idea, though the standard fixtures are a good inch wider (4 1/2") than a wide-mouth mason jar. Even a gallon jar lid is just too small. I might check by the dollar store, see if I can find any extra-large screw-top jars.

 

Quote

Have you looked at any of those slim line LED fixtures that almost look like recessed lights? They are only about  1/2" thick & range in size from about 5" - 15" in diameter. Harder to break & much less glare. More money though.

I hadn't. Cheapest option I see at HD is $30, though it's just shy of twice the lumens of my regular bulbs, so I'd only need two to replace the four bulbs I have right now. Food for thought, though I'd rather not re-wire my lights again, and I'd have to add a couple ceiling outlets to replace the ones at the base of my current lamp-holders.

 

 

I have some of those bare bulbs mixed in with my fluorescent tubes and I agree it adds some light from different directions.  Mine are high enough that they don't get in my sight lines.  

If the LED's you are using are truly cool to the touch you could try making a light diffuser from a gallon milk jug.  I can't promise it will look that great, in fact people will probably make fun of you.  But it might work.  

Anything that diffuses the light will also diminish it, so you might just want to try the milk jug idea to see if you like diffused light.  

You're using these for area or fill lighting, rather than task lighting? In general I prefer a way to control where the light goes, even if it's for an area or a diffuse fill, so I'm more in favor of hoods or solid shades. Plus they give more protection from accidental bangs and bumps. But really, it's whatever gives you the best working conditions. I'm a pragmatist, not a purist. :P

  • Author
21 minutes ago, ClassAct said:

You're using these for area or fill lighting, rather than task lighting? In general I prefer a way to control where the light goes, even if it's for an area or a diffuse fill, so I'm more in favor of hoods or solid shades. Plus they give more protection from accidental bangs and bumps. But really, it's whatever gives you the best working conditions. I'm a pragmatist, not a purist. :P

Yeah, these bulbs are just for fill, in particular since I have high shelves running around the top of my walls. Covering all those with task-lighting would be nice, but prohibitively expensive. If the ceiling were higher, I wouldn't worry about the shades, or maybe use something more traditional, but sub 8' means I don't have the flexibility I'd prefer. Also these are all LED's, so it would take one hell of a whack to do any real damage.

At this point I think I'm just going to end up going the DIY route. Nail up some wooden frames and cover them in paper as diffusers.

2 hours ago, BonPacific said:

At this point I think I'm just going to end up going the DIY route. Nail up some wooden frames and cover them in paper as diffusers.

You will lose a LOT of light that way, maybe 1/3 or more, even with the thinnest paper. Go to the home center & get some clear prismatic acrylic that's made for fluorescent light fixtures. It does a great job of reducing glare while transmitting almost all the light. You can cut it with a table saw, just go slow & use a crosscut blade.

20 hours ago, drzaius said:

You will lose a LOT of light that way, maybe 1/3 or more, even with the thinnest paper.

That's why, in the bad ol' incandescent days, we used clear bulbs rather than frosted white or other coating. You cut down the lumens with a coating, and then cut it down further with a shade. Hmm, this explains why my grandma's house was always so dingy and scary. Or maybe that was grandma. :P

7 hours ago, ClassAct said:

Hmm, this explains why my grandma's house was always so dingy and scary. Or maybe that was grandma.

That could be either of my wife's grandmothers.

On 5/19/2017 at 1:00 PM, BonPacific said:

 

At this point I think I'm just going to end up going the DIY route. Nail up some wooden frames and cover them in paper as diffusers.

I picked up some .010" polystyrene sheets a couple years ago for a thermo forming machine I never got around to building.  They've found a number of uses elsewhere since, but their number one use I've found for them are as light diffusers, particularly for photography.  It wouldn't take much work at all to make these into cylindrical or conical diffusers for bare bulbs.   If you look at the two project journals I posted, the light on the left (so the right hand shadow) is diffused through this material, and the right bulb (left shadow) is not.  You can see how much the light is softened by this material.

https://www.amazon.com/gp/product/B00E7W2Z0K/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

I think the price has gone up a bit since I ordered them, but you might find better pricing if you look around a bit.  This will be much more effective than paper.  Any thicker than .01" and it will block to much light, and less I think will let too much through.  As long as the bulbs don't put off too much heat (LED shouldn't), you shouldn't have too much concern over melting. 

  • Author

Thanks for the tips on using acrylic or styrene, I'll have to see what I can dig up locally.

 

I wonder if I'm slowly going blind, or have been spoiled by good task lighting, but the whole house is feeling darker than it used to. Maybe its time to go on a lamp-making binge.

Thanks for the tips on using acrylic or styrene, I'll have to see what I can dig up locally.

 

I wonder if I'm slowly going blind, or have been spoiled by good task lighting, but the whole house is feeling darker than it used to. Maybe its time to go on a lamp-making binge.

Decreasing light sensitivity is pretty common if you are over 40.....

  • Author
1 minute ago, wtnhighlander said:

Decreasing light sensitivity is pretty common if you are over 40.....

Well, I've got a little over a decade before I can lay the blame there. More likely my dayjob of staring into a computer screen.

Well, I've got a little over a decade before I can lay the blame there. More likely my dayjob of staring into a computer screen.

Yep, that doesn't help. Look into some UV or 'blue-blocker' glasses to help eye strain there. And if you have dry eye syndrom from screen time, the Optometrist my sis works for recommends flax seed oil suppliments to help with tear production. Wet eyeballs focus better, too.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.