oldman_pottering Posted June 10, 2025 Report Posted June 10, 2025 Some time ago I purchased a thin blade for my bandsaw, fitted it and hung the original ripping one up and promptly forgot about it. I want to do some ripping, grabbed the blade then noticed the condition of it Would you attempt to clean it or just replace it 1 Quote
Popular Post Coop Posted June 10, 2025 Popular Post Report Posted June 10, 2025 Just looks like surface rust. If so, I’d just use it as is and it will be clean before you know it. Might spray a little WD or oil on your bearing first. 3 Quote
oldman_pottering Posted June 10, 2025 Author Report Posted June 10, 2025 On 6/10/2025 at 12:28 PM, Coop said: Just looks like surface rust. If so, I’d just use it as is and it will be clean before you know it. Might spray a little WD or oil on your bearing first. It is just surface rust, I thought maybe it might have been bad for the wheels Good to know, thanks mate 1 Quote
Mark J Posted June 10, 2025 Report Posted June 10, 2025 I'd try it on some scrap first, it might leave some residue. Let us know how it comes out. 1 Quote
Don Z. Posted June 11, 2025 Report Posted June 11, 2025 My thought is if there is surface rust on the blade, it's probably on the "sharp" part of the blade too, which means it's no longer sharp. 1 Quote
Von Posted June 11, 2025 Report Posted June 11, 2025 I have two contradictory thoughts: it's probably fine and it's a $20? $30? blade and probably not worth messing with. 1 Quote
oldman_pottering Posted June 11, 2025 Author Report Posted June 11, 2025 On 6/10/2025 at 11:42 PM, Mark J said: I'd try it on some scrap first, it might leave some residue. Let us know how it comes out. Seems fine so far, tried it on a couple of small tree branches On 6/11/2025 at 11:21 AM, Don Z. said: My thought is if there is surface rust on the blade, it's probably on the "sharp" part of the blade too, which means it's no longer sharp. Oddly enough the rust only 'seemed' to be on the flat surface of the blade On 6/11/2025 at 10:37 PM, Von said: I have two contradictory thoughts: it's probably fine and it's a $20? $30? blade and probably not worth messing with. That's a good point, I think I'll order a new blade I basically have 2 blades, a 1/2 inch and 3/16, I need to learn to store the unused one away with some lubricant on it 2 Quote
wtnhighlander Posted June 12, 2025 Report Posted June 12, 2025 You might also consider 'stoning' the blade to clean it up. Some folks use a sharpening stone against the blade, while rotating in reverse, by hand. Saw unplugged, of course. The idea is to de-burr, and slightly thin down the spine of the blade to lower it's drag in the cut. A side effect is a clean, shiny blade. 2 Quote
oldman_pottering Posted June 12, 2025 Author Report Posted June 12, 2025 On 6/12/2025 at 10:29 AM, wtnhighlander said: You might also consider 'stoning' the blade to clean it up. Some folks use a sharpening stone against the blade, while rotating in reverse, by hand. Saw unplugged, of course. The idea is to de-burr, and slightly thin down the spine of the blade to lower it's drag in the cut. A side effect is a clean, shiny blade. Sounds like a good idea, thanks Quote
oldman_pottering Posted June 23, 2025 Author Report Posted June 23, 2025 Quick update, I ran this blade and it seemed ok. Couple of days ago I resawed a board that was 32mm thick and 700mm long, the process was going pretty good but got a bit scrappy towards the end I didn't think much of it but later I noticed the blade was some distance away ( 7mm )from the roller guide at the back of the blade that stops the blade from pushing back To my knowledge after fitting the blade I made all the usual setup adjustments but obviously something is out of whack I have now reset the top wheel tilt to align the blade correctly ( I follow the process that Alex Snodgrass uses) but havent done any test cuts When changing a blade is it necessary to adjust ALL adjustments each time ? 2 Quote
wtnhighlander Posted June 23, 2025 Report Posted June 23, 2025 Not usually, but it is wise to check them all, anyway. 1 Quote
Mark J Posted June 23, 2025 Report Posted June 23, 2025 I think you need to check all the adjustments. If you're mounting a smaller or larger blade you will have to adjust the thrust bearing (that supports the back of the blade). 1 Quote
oldman_pottering Posted June 23, 2025 Author Report Posted June 23, 2025 On 6/23/2025 at 11:24 PM, Mark J said: If you're mounting a smaller or larger blade Yep, I should have mentioned that I was changing in size Quote
Mark J Posted June 23, 2025 Report Posted June 23, 2025 For what it's worth, every time I change blades, I end up having to re-adjust every bearing. They never check out (and I use the Snodgrass method). 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.