Beechwood Chip Posted July 10, 2025 Report Posted July 10, 2025 Anyone have a miter saw stop with micro adjust that they'd recommend? I got the MatchFit Fold Down Stops a few weeks ago, but one of them has already broken at the hinge. Plus, I got tired of putting four playing cards between the stop and the work when batching out parts, so I'm willing to spring for something with micro-adjust. Or, I could just make something with a tapped hole and a bolt. Also, the off cuts occasionally get stuck behind the blade, so I'm ready to lose a little cut capacity for a zero clearance insert. I rarely take the saw out of 90°/90°, so I don't need one that will work at every angle. I have an old DeWalt and none of the nifty 3D printed stuff people are hawking on YouTube will fit my saw, so I'm looking for plans / ideas for a DIY solution. With dust collection, preferably. I've seen a bunch on YouTube, but I trust you guys more than I trust an influencer who also does woodworking. Quote
Von Posted July 11, 2025 Report Posted July 11, 2025 I don't have any solutions for you, just chiming in... I've found the zero clearance well worth it after too many small pieces getting pulled back into the saw and sometimes shot back out forward. I have a MatchFit dovetail grove on my saw with custom stops and am also doing the playing card thing right now. I bought some MatchFit Fold Downs as well since they were cheap, but haven't found the anticipated opportunity to use them, plus it's "too much work" to find the little hex key to move them. I find myself using my crosscut sled more for precise work, but that is personal preference. Quote
gee-dub Posted July 11, 2025 Report Posted July 11, 2025 +1 on the ZCI. Something to close the fence gap is a good safety improvement as well. Maybe some variation on this could help(?). 2 Quote
Beechwood Chip Posted July 11, 2025 Author Report Posted July 11, 2025 On 7/11/2025 at 8:03 AM, Von said: I bought some MatchFit Fold Downs as well since they were cheap, but haven't found the anticipated opportunity to use them, plus it's "too much work" to find the little hex key to move them. I drilled a hole in my miter saw station and parked the little screwdriver there. I figure I'll do something similar for every station where I use them. On 7/11/2025 at 8:03 AM, Von said: I find myself using my crosscut sled more for precise work, but that is personal preference. I keep forgetting about my crosscut sled. I made the mistake of building one that's huge and robust, with an inch and a half of MDF for the fence. So, it's a little annoying to drag out, but not annoying enough to build a new one. On 7/11/2025 at 8:03 AM, Von said: I have a MatchFit dovetail grove on my saw with custom stops and am also doing the playing card thing right now. I'll probably just tap a hole in my home made stop and use a 32 TPI bolt. One full turn is 1/32" of an inch, one quarter turn is 1/256", can't get much more micro adjust than that. @gee-dub That's perfect! Thanks! 2 Quote
BillyJack Posted July 11, 2025 Report Posted July 11, 2025 Why do you need a micro gauge on the miter saw.. Quote
Beechwood Chip Posted July 11, 2025 Author Report Posted July 11, 2025 On 7/11/2025 at 11:24 AM, BillyJack said: Why do you need a micro gauge on the miter saw.. I was needed 10 pieces to fit precisely into an existing space. So, I set the stop a bit long and cut one piece, did a test fit, added a playing card in front of the stop, and repeated until I had a perfect fit (four playing cards). Then I cut the remaining 9 pieces using that stop and four playing cards. I'd like to be able to creep up on a fit and then lock it in for repeatable cuts. Quote
BillyJack Posted July 11, 2025 Report Posted July 11, 2025 On 7/11/2025 at 10:37 AM, Beechwood Chip said: I was needed 10 pieces to fit precisely into an existing space. So, I set the stop a bit long and cut one piece, did a test fit, added a playing card in front of the stop, and repeated until I had a perfect fit (four playing cards). Then I cut the remaining 9 pieces using that stop and four playing cards. I'd like to be able to creep up on a fit and then lock it in for repeatable cuts. I’ve used the same miter stop since 90’s without an issue. Do you have a miter. Guage on your saw? Quote
Beechwood Chip Posted July 11, 2025 Author Report Posted July 11, 2025 I have a miter gauge and a sled for my saw. Could have used those. I just use the miter saw for cross cuts out of habit. Quote
BillyJack Posted July 11, 2025 Report Posted July 11, 2025 I rarely use tye table saw for anything complicated. Quote
Popular Post gee-dub Posted July 11, 2025 Popular Post Report Posted July 11, 2025 There are absolutely people out there who are masters of the RAS and CMS . I use the tablesaw as a joinery machine about half of the time. We all develop methods of work that work for us. Sharing our methods and operations opens up new ideas for everybody. 3 Quote
BillyJack Posted July 11, 2025 Report Posted July 11, 2025 On 7/11/2025 at 10:53 AM, gee-dub said: There are absolutely people out there who are masters of the RAS and CMS The RAS is an old school tool that has been replaced. i rarely use the RAS since I stopped making cabinets.. Quote
Chet Posted July 11, 2025 Report Posted July 11, 2025 On 7/11/2025 at 8:55 AM, BillyJack said: The RAS is an old school tool that has been replaced. Not by everybody. Quote
gee-dub Posted July 11, 2025 Report Posted July 11, 2025 On 7/11/2025 at 12:53 PM, Chet said: Not by everybody. Too true. Just as there are folks out there who recommend brushing your teeth with a router, there are folks who think a RAS can do anything . I am not among either group Quote
Beechwood Chip Posted July 11, 2025 Author Report Posted July 11, 2025 On 7/11/2025 at 4:02 PM, gee-dub said: Too true. Just as there are folks out there who recommend brushing your teeth with a router, there are folks who think a RAS can do anything . I am not among either group Of course! Obviously, you should brush your teeth with a Dremel, not a router! 1 Quote
Coop Posted July 12, 2025 Report Posted July 12, 2025 @BillyJack, why did you stop making cabinets, retirement? Quote
BillyJack Posted July 12, 2025 Report Posted July 12, 2025 On 7/11/2025 at 8:42 PM, Coop said: @BillyJack, why did you stop making cabinets, retirement? I worked in a commercial shop last and the guy I had worked for was almost 70. Last job he lost a lot of money because he didn’t meet the deadline. I was out of a job as he decided to shut down and retire. Out of work I noticed a “Furniture Maker” position in Kansas City.. Applied and got the call I had the job.. In 2017 the doctors decided to pull my kidney and this would make me stage 5 disabled. With company having top head issues with money they decided to part ways, so I had the surgery and went on disability. They eventually folded.. 1 Quote
BillyJack Posted July 12, 2025 Report Posted July 12, 2025 On 7/11/2025 at 2:53 PM, Chet said: Not by everybody. It’s been replaced, but if you want to use it, by all means use it.. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.