woodup Posted August 4 Report Posted August 4 Just finishing up my rocker build. Starting the the final sanding. To what grit do you guys recommend that I sand? Thank you for your time!! Jeffrey 2 Quote
Popular Post pkinneb Posted August 4 Popular Post Report Posted August 4 Welcome to the forum!! RE your question knowing the wood and finish would help provide better answers but in general I usually go to 150 /220 prior to finish and then as high as 320 and in some cases higher after applying finish. 3 Quote
Popular Post gee-dub Posted August 4 Popular Post Report Posted August 4 Welcome and pkinneb is right on. The grit you stop at is relative to your material and your finish. If I am using shellac, I sand to 400 at least. Shellac goes on thin, thin, thin and with multiple coats. For open grain woods like ash or oak I go to 220 and still get good absorption with oil based finishes. For cherry and walnut I will go to 320 or higher on exposed end grain. Wouldn't it be nice if there was just one answer? I will also use lower or higher grits to make the coloration (if any) appear lighter or darker. Finer grits allow less pigment to settle into the material, coarser grits allow great absorption and therefor more intense color. I can't say it enough . . . test boards, test boards, test boards. Know what is going to happen on your test board before you commit to your actual piece. 3 Quote
woodup Posted August 4 Author Report Posted August 4 Thank you for your help. I an working with walnut and an oil finish. 1 Quote
Von Posted August 4 Report Posted August 4 4 minutes ago, woodup said: Thank you for your help. I an working with walnut and an oil finish. That's going to look gorgeous. Echoing others, with an oil finish I would go at least 220 on the faces and 320 on the end grain. Doing a test board first is worth it to make sure you like the look and work on the process. 1 Quote
gee-dub Posted August 4 Report Posted August 4 I am a firm subscriber to the saying "if it's worth making, it's worth making out of walnut". So many colors, shades and figures. These are all sanded to about 220 with 320 to 400 on the exposed end grain. They are all done with an oil varnish blend using the wipe on, break for coffee, wipe off method. Oops! Except the first one it is done the same but then I added a lacquer to the top and pulls since it primarily lives in the grandkid's room and can get poorly used. 2 Quote
Popular Post wtnhighlander Posted August 4 Popular Post Report Posted August 4 If you happen to be using 'Danish' oil, I suggest wet-sanding the oil as you apply it, with 600 grit or higher. The slurry from this process helps fill the pores, giving a smooth, buttery result. Its a slow process, and requires multiple coats, but the result is like no other. Sand the wood to 320. Flood on danish oil, wet sand withh 600, wipe off excess. Wait 24 hours, then repeat. And repeat. And repeat ... until you are satisfied. My experience is 4 to 6 coats, depending on the wood species. 3 Quote
Popular Post woodup Posted August 5 Author Popular Post Report Posted August 5 Thanks for the quick replies. Very helpful. I start sanding in the morning. Gee-dub, thanks for the inspirational photos. Very impressive!! I taught sculpture at the collage level and showed students works other artists in various fields. . it gave them food for thought. thanks everyone for your thoughts. 3 Quote
Popular Post Beechwood Chip Posted August 5 Popular Post Report Posted August 5 On 8/4/2026 at 8:18 PM, woodup said: I taught sculpture at the collage level and showed students works other artists in various fields. Sounds interesting! I hope you'll continue to hang out here and be part of our community. 4 Quote
dwilliam Posted August 6 Report Posted August 6 I'd stop at 180–220 grit for most hardwood rockers. It leaves a smooth surface while still allowing a quality finish to bond well. Sand evenly, remove dust thoroughly, then apply your finish. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.