Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Rust Removal

Featured Replies

I have not had to tackle this in the past as I was always active in the shop. When COVID hit I was shut down and have not had a project since. 
I am now getting back into action and I need to remove rust from my cast iron tables. Does anyone have a good technique for this?

Here's my procedure for maintaining cast iron tables

    (Pasting a Google Doc outline into WTO is terrible, the formatting gets completely screwed up.  And it looks fine until you save, then it goes all wonky.  So I have to keep editing and saving to see what it really looks like.  I give up, this is close enough.)

WD40 and maroon Scotch Brite pad and ROS sander to remove rust. Do entire surface evenly, not just rust spots

Naptha or mineral spirits and wipe off with blue shop towels or rags, to remove dirt and any moisture. Let rags dry before throwing out

CRC 3-36 and buff to protect surface from rust and lubricate surface. You can use buffer, or buff by hand

Rex Krueger just did a short about rust removal.  tldr; wire brush wheel for hand planes. 

  • Author

Thanks Beechwood, I had the WD40 and Scotch Brite in mind because I have these in the shop. Thank you for your expert input.
 

For hand tools and the like that you can put into a container, I recommend Evaporust.

Vinegar works but I've had it weaken thin metal enough to cause it to break.

 

On 11/3/2026 at 8:48 PM, Steve B Anderson said:

Thank you for your expert input.

Oh, that's not expert advice, that's just what I do based on YouTube research.  I've done it a few times and it didn't destroy anything.

Don't forget ventilation and organic filter respirator if you're using naptha and mineral spirits indoors.  We just had a thread about passing out from fumes.

  • Author
On 11/3/2026 at 8:52 PM, Beechwood Chip said:

Oh, that's not expert advice, that's just what I do based on YouTube research.  I've done it a few times and it didn't destroy anything.

Don't forget ventilation and organic filter respirator if you're using naptha and mineral spirits indoors.  We just had a thread about passing out from fumes.

Just trying to give you a bump Bud

  • Author
On 11/3/2026 at 7:51 PM, Von said:

For hand tools and the like that you can put into a container, I recommend Evaporust.

Vinegar works but I've had it weaken thin metal enough to cause it to break.

 

Thanks for the tip Von.

I had a couple sanding blocks, made from a friable rubber that had grit embedded in them all the way thru, decades ago; I can't remember their brand name (hopefully someone here remembers).  

They were lousy to use on wood, but when my tools all rusted up in North Dakota they worked fantastic for removing rust, from everything from my tablesaw table to my handplanes.  Moving to UT was the permanent solution.  ;)

27 minutes ago, Botch said:

I had a couple sanding blocks, made from a friable rubber that had grit embedded in them all the way thru, decades ago; I can't remember their brand name (hopefully someone here remembers).  

They were lousy to use on wood, but when my tools all rusted up in North Dakota they worked fantastic for removing rust, from everything from my tablesaw table to my handplanes.  Moving to UT was the permanent solution.  ;)

I think you are thinking about Sandflex Hand Blocks? If so, I agree with you, it's never occurred to me to use them on wood, but I find they very useful for treating smaller rust spots and generally cleaning up tools.

  • Popular Post

@Steve B Anderson

I've been using evapo rust for approximately 10 years First came across it in my local Florida Napa center and because there are parts store and they sell paint and all that other stuff it seemed like it was a good product and I gave it a try by 2019 I found that Amazon had it for a little bit less about $22 recently this year I bought more and it was $28 the same gallon.

It has changed a little bit over time but the effectiveness is still just there.

The word of caution never use the gel on surfaces because it dries a  turns white and digs into the metal Not worth it.. Naval gel is very similar it turns the metal white and it digs into the Metal and what I mean by that he is a great pock marks that cannot be fixed.

I go about a little bit differently than others.

When I inherited my father's tools like joint to a planar drill press and many others The cast iron surfaces were badly rusted because stuff was laid on top of them moisture got trapped in between and rusted fair a lot.

So what I did and these are the steps I use is I took a green scrub dry using no fluids of any kind no WD40 no mineral spirits nothing just dry.

I did not want to sand it because sanding creates other problems I do not want. do use a wire wheel it because you could dig in without realizing it.

I have one of those ancient double sided wood scrapers kind of like AU shape I had years earlier around to the corners a little bit so the corners couldn't dig in and very evenly scraped across and got the last of the high spots of rust off using the vacuum constantly to get the small bits picked up and use the green scrubby again It looked pretty good at that point. 

You can use compressed air but it must be absolutely dry otherwise you drive moisture back into the pores of cast iron Cast iron is extremely porous.

My next step was to use Dawn add a green scrubby again and wash the top by the way the machine was already torn down south there's nothing to get wet that matters.

Just the top of the machine The reason this step was done was to remove any oils previous wax whatever else that made it on the top Evapo rust does not remove oils nor will it penetrate through it It has to be clean that's why in some very large machine shops they steam clean the engine blocks and then put it into 120 degree tank of evaporust and use ultrasonic vibrators on the sides and the block looks like it had been machined This is not my idea there's lots of good articles in the machining forums of using this method.

Using a large trash leaf bag 55 gallon Make sure there's no holes in it because otherwise it's got you don't want to lose the fluid.

So I used of cardboard box  to build like a coffer dam around the table using dowels chopsticks whatever you want in the four corners that allows the fluid to be in contact with the metal top and not would totally immerse the entire slab of metal.

Whatever you use create the gap it needs to make the least amount of'cause it will leave a mark where the fluid was not able to stay in contact with real well.

Open the bag every few hours and agitate the solution around and we go to take it out slippery and it's gonna be black That's the carbon that was released between the pores It's OK. Take it out in the yard It will not kill the grass and wash down thoroughly Use a little bit of dawn again and a basically wore out green scrubby and wash it again and see if you need to put it back into solution again for another 24 hours.

 

If you're satisfied with the outcome the next step I use because I still have it and it cannot be bought anymore because it's no longer made. 1339084781_19001503ImageSCJohnsonPasteWax.jpgYellow Can Johnson's paste wax for wood makes a great sealer and it does not leave stains on the wood as you work on it.

Word of significant caution never use any automotive wax on cast iron tops they will leave silicone and other oils that will not appear till you go to your final phasing stage and you end up with fisheye and other circular marks that are almost impossible now to remove.

I'm told and found out on woodworking forms that bowling alley wax is made of the basic same properties.

Johnson’s Paste Wax is made from a blend of carnauba wax, paraffin wax (and/or hydrocarbon waxes), and chemical solvents like deodorized naphtha (or Stoddard solvent) and 1,2,4-trimethylbenzene

Discontinuation: SC Johnson officially discontinued its iconic paste wax product in 2021.

Because I live in Florida the next step was easy Let the table top sit in the sun the direct sun get hot to make sure it's absolutely dry no moisture content left.

Then put a thin layer of the paste wax on rubbing it in thoroughly letting it dry to haze and see if it's evenly covered if not reapply while still hot and let it dry again it should be now very uniform Bump the top out thoroughly Let it cool overnight and buff it again you'll find now whatever you put on top we'll slide across nice and smoothly.

 

I believe the product Evaporust is a good product and can be used on lots of different iron and steel products without doing damage to them it just turns the bonds that hold the rust together loose and allows it to wash away.

 

Good luck in your endeavors restoring your good working equipment.

 

It's another grand day on the farm! Joe

Edited by Biotec
Fix some spelling errors

I was looking for Jack Fosberg's video on this and found this old thread from here.  I still use the same method for tool tops.  I use Evaporust for things that I can leave soaking in it.  For some reason the video I had posted earlier in the thread has been changed, but you can find it in Lee Bussey's post farther down in this old thread:

 

  • Popular Post

I've said this before, but it bears repeating. The best protective coating against rust is ....

rust.

A cast iron table with deep rust pitting would certainly need resurfacing, but fine surface rust, lightly burnished and combined with paste wax / furniture wax, is the same 'browned' treatment used to protect firearms for centuries. If you can live with a bronze-colored table, rather than shiny silver, this is 100% the least-effort option for maintaining your cast iron or steel machine parts. I did this to my saw table about 8 years ago. It resides in an un-conditioned shed, where humidity stays above 90% far more that it drops below 60%, and the table is still smooth as butter.

@wtnhighlander

Good day

I had forgotten I didn't mention it before but some of the furniture racks that's on the market is lots of Lots of silicon in it. This Is as bad as automotive wax.

Hear some online trivia that I forget about.

here some of the brands that have it below.

Wood wax and furniture polishes containing silicone provide an immediate, slick high-gloss shine and repel dust effectively, but woodworkers and restorers generally advise against using them on fine or antique wood. https://www.popularwoodworking.com/finishing/understanding-furniture-polishes/  this from August, 2020 so it still shows the yellow can Johnson Paste.

 

Examples of Products Containing Silicone & Wax/Oil
  • Husky 1200 Furniture Polish: A lemon oil, wax, and silicone emulsion spray designed for woodwork, desks, cabinets, and laminated surfaces. 
  • Premium Wood Polish (e.g., Mr. Janitorial / commercial formulations): Ready-to-use liquid formulas containing carnauba wax and silicone for high-gloss, slow-to-dull finishes. 
Why Silicone is Controversial in Wood Polish
  • Refinishing Complications: Silicone penetrates wood finishes and acts as a contaminant. As discussed by woodworking enthusiasts on Reddit r/finishing, silicone makes future touch-ups, repairs, or repainting extremely difficult, often causing "fisheyes" or rejection of new topcoats. 
  • Build-Up and Haze: Over time, silicone layers can accumulate, attract dirt, and react with other products to turn into a cloudy or milky-white haze. As noted on Howard Products FAQ, silicone does nothing to actually nourish or condition the dry wood underneath. 
  • Expert Consensus: According to guides like Popular Woodworking and Home-Ec 101, manufacturers often omit silicone from ingredient lists, and mixing silicone polishes with traditional natural waxes leads to streaking and softening of the finish. 

Also of note I also have poor workshop conditions.

My garage is unconditioned No true ventilation so heavy rains here in north Central Florida will make the shop damp for a while.  Some moisture comes up through  floor with severe rains that saturate the ground.

most of my equipment the big heavy stuff that I'm not actively using lives in a 8 by 12 trailer. Sitting in the driveway in front of the garage area.

I do most much woodworking out on the driveway and access the tools.

The garage itself is for small projects assembly and stuff that takes time and most equipment has been evicted into the trailer Therefore moisture is a significant issue of cast iron After the number of the pieces have been restored They've had the Johnson paste wax applied to them I have not had to renew it except on the jointer planer when I noticed it was getting a little difficult to slide across so buffed it out reapplied buffed it out again and it is just as shiny as ever. Most were restored in 2019 and most of the tools are from the 1980s.

They were hand me downs from my father after he passed away.

 

I have bought a lot of older tools from flea markets and so forth that were pretty ratty looking. with mild rust to significant rust in some cases and the Evapo rust has made it easy to restore them.

 

  • Author

Thanks for all the great tips guys. I can definitely make a plan with all this information.

l actually have some Johnson wax left over from the good’ol days.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.