Southwood Posted March 24, 2012 Report Posted March 24, 2012 Picked up a 5 1/4 today and 2 #7's . Don't be discouraged when looking, they are out there. Trying to upload pics and it is a no go. Quote
Vic Posted March 25, 2012 Report Posted March 25, 2012 I grabbed this off of G+ for ya, Steve. Nice score! Quote
Southwood Posted March 25, 2012 Author Report Posted March 25, 2012 Thanks Vic, I didn't even think about that. Quote
tdale51@yahoo.com Posted March 25, 2012 Report Posted March 25, 2012 What's the purpose of the grooved sole? Quote
Vic Posted March 25, 2012 Report Posted March 25, 2012 What's the purpose of the grooved sole? Two thoughts on that: 1) it decreases friction 2) a marketing gimmick, claiming decreased friction I tend to think the latter, although I do have a Sargent jointer that is grooved. It just happens to be the one I got at an estate sale. Quote
Southwood Posted March 25, 2012 Author Report Posted March 25, 2012 I have never really noticed a difference between the two bottoms. Although, I tend to use the smooth bottoms the most. Quote
wilburpan Posted March 25, 2012 Report Posted March 25, 2012 Two thoughts on that: 1) it decreases friction 2) a marketing gimmick, claiming decreased friction You forgot one. 3) A feature to give collectors one more thing to obsess over. 1 Quote
Brian VanVreede Posted March 25, 2012 Report Posted March 25, 2012 Sweet! What condition are the blades in? Quote
Southwood Posted March 25, 2012 Author Report Posted March 25, 2012 Little more research. According to Rexmill site, the 7-c is a type 9, 7 is a type 11 and the 5 1/4 is a type 16. The blades are all in good shape as could be. They have some life left in them for sure. The 7-C has a Sweetheart blade in it, so I wonder if it didn't see quite a bit of use. Quote
Vic Posted March 25, 2012 Report Posted March 25, 2012 I put new Hock blades in all my rehab planes. I've never regretted the decision. Much more substantial than what any of them had originally. Quote
Southwood Posted March 26, 2012 Author Report Posted March 26, 2012 I generally use the Veritas replacements. Had good luck with them so far. Quote
TimV Posted March 26, 2012 Report Posted March 26, 2012 Just finished restoring a Bailey #7 last night. I was fortunate this time that nearly all the japaning was in great shape. This one has a smooth sole. Here's a tip on flattening the sole. I used sandpaper on my melamine extension wing of my table saw. I always start with 80 grit and make sure that the plane is fully assembled with the blade in but pulled way up and tight. However, on these longer planes, there will probably be a lot of high/low spots. You'll immediately see this with a few passes over the 80 grit sandpaper. Once I see this, I take it to my 6x48 stationary belt sander with an 80 grit belt. Use a dust mask because it generates a lot of fine cast iron dust. Place the plane on the sandpaper and sand down until the lowest spots just begin to dissappear, then take it back to the sandpaper by hand. Work your way through grits, 80,100,150,220,320,400,500,600,800,1000,1200. The last several are up to you (I like a nice finish, but that nice is probably unnecessary). Do it dry and just shake tap off the cast iron dust occasionally. I enjoy restoring planes Good luck with yours. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.