STL Woodguy Posted June 28, 2012 Report Posted June 28, 2012 I've been hemming and hawing about a jointer the last few months and keeping an eye on Craigs List. Unfortunately everything is either six inch jointers, or on the rare occasion a decent Grizzly 8" one comes up, it's too far away. I've noticed this Powermatic 60: http://stlouis.craigslist.org/tld/3091522824.html Originally he posted it at $1200, then knocked it down to $800, so I think he's having a hard time selling it (bargaining room on my part, maybe). I'm not thrilled about the current price, because a Grizzly 8" parallelogram can be had for nearly the same price. And this is NOT a parallelogram jointer, right? On the other hand, it is a Powermatic, and isn't the new price around $2000 for this guy? The size is right for my space (the Grizzly is a bit longer). Also, it's not too far of a distance to rent a truck and go get it (much cheaper than Grizzly freight). I don't know the condition of the unit yet, I would need to investigate and see it demoed first ... from what I see from the pics, it's just sawdust dirty. Provided that it is in great shape and does work well, would it be worth the price for a Powermatic or would I be smarter going for a Grizzly? Or, what 'would' a reasonable price be for this? Quote
HuxleyWood Posted June 28, 2012 Report Posted June 28, 2012 This is a dovetail way jointer not an issue in my book but if/when it gets out of alignment it is harder to adjust. That one was made in the US so hard to figure what a new price would be. Note it will need a flange for proper dust collection. These were well built solid jointers, though I would rather have an earlier evergreen version but it still trumps the current Asian machines regarding quality. I still think it is a little high but if it checks out I would prefer it over a Grizzly and depending on the used market near you I wouldn't feel cheated at $800 though I am more a fan at 650-700. Quote
Trip Posted June 30, 2012 Report Posted June 30, 2012 That's a decent jointer. It's OK at $800 if in really good condition. The motor is a Baldor, so that is worth a few $$... Quote
STL Woodguy Posted June 30, 2012 Author Report Posted June 30, 2012 Been thinking on it and the things I like about that unit is that it can run on 110v, and that the length will fit well into the remaining space in my small shop. Yep, just noticed the missing flange, but can easily replace that. Think I'm going to go check it out in the morning, and see if I can bargain down with cash on the spot if it checks out. Quote
HuxleyWood Posted June 30, 2012 Report Posted June 30, 2012 Yep, just noticed the missing flange, It isn't missing it was just never there, old school didn't pay much if any attention to dust collection, the big PM planers didn't come with dust hoods, I have been in several lumberyards with the chips just flying in an arc out of the top of a PM 221 into what was often a HUGE pile. Quote
wdwerker Posted June 30, 2012 Report Posted June 30, 2012 Planer and joiner chips aren't dust in my book. Sometimes it is easier to shovel up chips than to keep dumping the drum ,not to mention clearing clogged lines ! Quote
HuxleyWood Posted June 30, 2012 Report Posted June 30, 2012 Planer and joiner chips aren't dust in my book. Sometimes it is easier to shovel up chips than to keep dumping the drum ,not to mention clearing clogged lines ! Certainly the "chips" aren't dust but there is PLENTY of dust and lung clogging fines in jointer and planer offcast. Just use a Dylos particle meter and you will see. However, it isn't nearly as bad as what comes of a drum or widebelt. Quote
STL Woodguy Posted June 30, 2012 Author Report Posted June 30, 2012 I don't care if it's dust or chips, I don't want it on my floor either way. So here's the story: I went and now I'm back...with the final piece of my workshop in tow. Not sure how old this unit is (owner was out), I'm guessing it's from the 80s. The base is worn from age, but that doesn't make a difference. The bed was in great condition and while it's seen it's action, no rust whatsoever, just needs a good wipedown and maybe some protection and waxing. As already stated, no flange, but I already have one which I will just bolt on. Jointed like a dream, I jointed a crooked board I brought with me and I dunno, there's just something devilishly gratifying about setting a flattened board down and getting that 'suction' on the bottom. Better yet, making it that way in under 30 seconds rather than trying to shim planer sleds or trial and error with hand planes. The unit passed the nickel test with flying colors and I also liked how 'small' the unit was. I have only a limited amount of space left and while I could technically fit the Grizzly in there, that unit is bigger and this Powermatic would fit beautifully in the space I have left for a jointer. Yet, the wings are plenty long for long boards, all I will ever likely need. Best of all, the unit is heavy, but not impossibly heavy. Ate breakfast and thought it over, then tried to talk the woman down to $725, but she said that the owner had already knocked it down from $1200 (which I wouldn't have paid) and would go no lower. Took more time to consider it and as I would not have to rent a pickup truck to get this guy, not have to burn the gas to drive down to Grizzly down south to preview their jointer (and I would still have to freight it at that), and that the seller was a woodworking shop not likely to budge on price as much as an eager / undereducated private seller would, I decided to play ball and meet their price. Proving that Siegfried and Roy aren't the only masters of the impossible, I got the jointer completely disassembled and with staff help, managed to get a freakin' 8 inch jointer into a Toyota Corolla. ("You're GOOD!" said the guy at Rockler on the way back.) Only issue was that I'm somewhat of a hermit and can't call on help with a snap of my fingers, so getting it out of the car was going to be a challenge. Not to mention it's well over 100 degrees today and I didn't want to leave it out in the heat. Should of thought of that first, but I'm spontaneous and deal with things as they come. I had a hand truck (one of the most valuable things I own), so the base (with motor intact) was no problem. With very clever use of the hand truck, boards, strength, levers and maneuvering, managed to get the top into my back area and just parked it in the shade for now. It's only a short ways into the kitchen, so after I cool down a bit, I'll wheel it on in. Getting it down the stairs into the basement will be a challenge and although I've gotten a bandsaw down there on my own before, that was in a crate and I'll likely wait until I can get someone over here before I do that. So long as it's inside and out of the heat, I'm good. The only complication in the whole thing came when the bumper of my car got badly scratched when the guy at the shop and I were getting it into the back. (Had a towel laid down, but it fell during loading.) Oh well, I may buff that out with my Rotex sometime and see if I can hide / repair that, but I'm not mad, just goes with the territory. So all in all, I think it was worth the price to be done with the whole thing, no renting trucks, waiting on freight trucks, haggling about lift fees, etc. Better yet, no more hot glue and planer sleds. Anyway, other than getting it into the basement, reassembling it and readjusting the fence and beds, I still have to deal with the fact that the unit uses 220v. It's convertable to 110v (and the shop guy said their other 8" Powermatic ran just fine on 110v), but I'm not sure yet whether I keep it set to 220v and change the plug out for a dryer plug, or set it to 110v. Just care about taking a well earned rest for now Quote
HuxleyWood Posted June 30, 2012 Report Posted June 30, 2012 Great story. Based on color it has to be 80s or 90s. What is the serial number? That late the first two digits should be the year. Quote
STL Woodguy Posted June 30, 2012 Author Report Posted June 30, 2012 I got balsy and managed to get it down to the basement. I will not say how, it went fine but it's not recommended. Just going to say thank god for carpet, I won't get my renting deposit back (but I blew that long ago), and I'm retiring from transporting machinery up and down (I'm hiring the local moving men when I eventually move out). I have everything I need now and anything I bring home from here on out to add to the shop will be in a systainer with a handle. I spotted the serial number and went online to check it out, appears this unit is from 1987. Quote
HuxleyWood Posted June 30, 2012 Report Posted June 30, 2012 I spotted the serial number and went online to check it out, appears this unit is from 1987. So the first 4 digits are 8761- Quote
TimV Posted July 2, 2012 Report Posted July 2, 2012 Well it sounds like you got it. What was the final $? Quote
STL Woodguy Posted July 2, 2012 Author Report Posted July 2, 2012 As I said, $800, they wouldn't go lower. Not a steal by any means (though I'm jealous of those who got away with this for $400-500), but it is in line with what I've seen similar units being sold online. I'm just glad to be done with it (other than solving the 110v / 220v dilemma). Quote
HuxleyWood Posted July 2, 2012 Report Posted July 2, 2012 . I'm just glad to be done with it (other than solving the 110v / 220v dilemma). Do whatever is cheaper and/or easier, you won't see a difference in use, it will make the same power on 120 as it will on 240, period. The only thing you may notice is it will spin up a little faster on 240v, but by the time you start it and get a peice of wood on it it will be up to speed on either voltage. Quote
STL Woodguy Posted July 2, 2012 Author Report Posted July 2, 2012 It's simply a matter of convenience, but with dead ends. Pretty much chronicled in the second half of the 220v thread nearby. The TL;DR version: saw is currently wired for 220v, need a 10-30 dryer head to hook it up, no one sells a 10-30 dryer head but only the whole dryer cord, longest cord is 6' and I need 8-10'. Now that I've located a wiring diagram and have a guy at work who knows more, looking likely I'll go 110v. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.