rodger. Posted November 8, 2012 Report Posted November 8, 2012 I have been watching lots of podcasts on this, and may be interested in buying one (the smaller version). Here in Canada, a Festool Domino 500Q runs a whopping 950 dollars. In all the material I watched, a question I was wondering was never really mentioned. I would use the domino to cut joinery for table aprons and legs mostly (I do this now with mortise/tenon). Most people use the domino like a biscuit joiner, drawing a line and then plunging according to the line. Is there any "wiggle" room in the joint (to line the top of the apron up with the top of the leg)? All the joints I have seen cut online are pretty tight. If there is no "wiggle" room, is the reference pin/dog suitable for cutting the mortises? It really drives me nuts when the top of the leg isn't flush with the top of the table leg. Quote
PaulMarcel Posted November 8, 2012 Report Posted November 8, 2012 Like any tool, there are calibrations. For the most part, it comes calibrated out of the box. For me, the cursor was out of calibration, but it's a simple 5 minute calibration and I've only had to re-do it for making a video on how. My joints come up as flush as you'd want. There really isn't any wiggle room unless your Dominos are ridiculously dry. Even out here in AZ they are snug. That said, even if everything is calibrated, you might not get flush joints if you're sloppy with it. Since a hair out of flush drives you nuts, I'm betting 'sloppy' doesn't apply here Meant to add this link first time around: http://blog.festoolusa.com/post/2012/06/28/The-Ultimate-Festool-Domino-Guide.aspx Quote
STL Woodguy Posted November 8, 2012 Report Posted November 8, 2012 Alignment to the top, I've had no issues right out of the box. Left to right is a different story. Paul's video is good on how to calibrate that, though admittedly I should spend a little more time to get the calibration a little better on mine. So far I've followed the practice of cutting a slightly wider slot on one side of the workpiece (as suggested in the manual) for some wiggle room, and so far that has worked fine for the particular projects I've been working on. Quote
Nick2cd Posted November 10, 2012 Report Posted November 10, 2012 franklin, the domino can be as accurate with no wiggle room or sloppy as you'd like. if you leave it set on exact width of the dominos and use a fine pencil mark (.5mm mechanical pencil is my tool of choice) you will have a very flush and tight fitting joint. however, there are things that can influence your fit and finish (ask me how i know). you need to use good technique with the domino. example, a slow plunge in harder woods works best. holding the tool back near the power cord during the plunge gives you better control than on the main body of the tool. and most importantly, the domino is much more accurate with dust collection than without. i made my first 10-15 joints without dust collection and then started using dust collection.....makes a huge difference. i attribute this to not having chips in the mortise that wedge between the cutter and the wall of your mortise (which would consequently push the tool from side to side on a micro level). it's not the best pic, but here's a joint i did for my son's bassinet that would be similar the the type of joint you'd like to cut. in fact, every joint on this bassinet was done with my domino. this was my first "fine furniture" type of project. oh and lastly, for aprons to legs, you could very easily get away with no pencil marks at all and just using the built in paddles on the domino if you are placing a single domino. if you want 2 dominos per apron, use the paddle for the first one and then the trim stop for the second one. hope this is helpful to you. 1 Quote
rodger. Posted November 10, 2012 Author Report Posted November 10, 2012 franklin, the domino can be as accurate with no wiggle room or sloppy as you'd like. if you leave it set on exact width of the dominos and use a fine pencil mark (.5mm mechanical pencil is my tool of choice) you will have a very flush and tight fitting joint. however, there are things that can influence your fit and finish (ask me how i know). you need to use good technique with the domino. example, a slow plunge in harder woods works best. holding the tool back near the power cord during the plunge gives you better control than on the main body of the tool. and most importantly, the domino is much more accurate with dust collection than without. i made my first 10-15 joints without dust collection and then started using dust collection.....makes a huge difference. i attribute this to not having chips in the mortise that wedge between the cutter and the wall of your mortise (which would consequently push the tool from side to side on a micro level). it's not the best pic, but here's a joint i did for my son's bassinet that would be similar the the type of joint you'd like to cut. in fact, every joint on this bassinet was done with my domino. this was my first "fine furniture" type of project. oh and lastly, for aprons to legs, you could very easily get away with no pencil marks at all and just using the built in paddles on the domino if you are placing a single domino. if you want 2 dominos per apron, use the paddle for the first one and then the trim stop for the second one. hope this is helpful to you. Thanks - good info here. How far is the closest index pin from the cutterhead? For example, if I were to cut a mortise in a table leg using the closest index pin to the cutterhead, how much space is left between the top of the leg and the start of the mortise? Quote
Nick2cd Posted November 11, 2012 Report Posted November 11, 2012 Thanks - good info here. How far is the closest index pin from the cutterhead? For example, if I were to cut a mortise in a table leg using the closest index pin to the cutterhead, how much space is left between the top of the leg and the start of the mortise? not sure on this. i'll have to check Quote
Trip Posted November 11, 2012 Report Posted November 11, 2012 My recommendation, go to a local woodcraft and play with one. no question it's an expensive piece of kit -- but for many, it's well worth it. You can build-in some wiggle-room in the joint by using the 'width' setting. again, i'd get my hands on one so that you can see for yourself. i love mine and have both the 500 and 700 units. it's one of the few tools introduced in the past decade that has really changed my approach to projects. after a while, you really start to 'think domino' when looking at something that would be traditional m/t. Quote
rodger. Posted November 11, 2012 Author Report Posted November 11, 2012 My recommendation, go to a local woodcraft and play with one. no question it's an expensive piece of kit -- but for many, it's well worth it. You can build-in some wiggle-room in the joint by using the 'width' setting. again, i'd get my hands on one so that you can see for yourself. i love mine and have both the 500 and 700 units. it's one of the few tools introduced in the past decade that has really changed my approach to projects. after a while, you really start to 'think domino' when looking at something that would be traditional m/t. I don't have a woodcraft, they don't sell in my area (perhaps not even in Canada). Lee Valley sells Festool, but there are no demo days coming up listed on their website. Maybe I'll call them on Monday and see if I can get my hands on one to try. Thanks for the suggestion. Quote
Trip Posted November 11, 2012 Report Posted November 11, 2012 Also think of local cabinet shops -- there should be someone that may be able to show you some kit. You can try the FoG web forum for folks in Ontario with kit. Quote
PaulMarcel Posted November 11, 2012 Report Posted November 11, 2012 Thanks - good info here. How far is the closest index pin from the cutterhead? For example, if I were to cut a mortise in a table leg using the closest index pin to the cutterhead, how much space is left between the top of the leg and the start of the mortise? For the 500: Inside edge of the locator pin or paddle to the center of the mortise is 37mm. Width of an exact-size Domino slot is 13.5mm+Domino diameter (5, 6, 8, or 10mm). The medium mortise width adds 3mm, large adds 6mm. Quote
wdwerker Posted November 11, 2012 Report Posted November 11, 2012 There is also a small 4 mm domino. If you cut the joint on the exact setting and it is a tiny bit off when you dry fit the joint a quick sand or shave to the domino tenon and you are fixed. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.