Festool Domino....how much accuracy should i be expecting?


Recommended Posts

Posted

I've had a domino for about a year now but really have only used it on one project. i haven't had much shop time, as life has gotten in the way. but that's neither here nor there. anyways, i am finally using it on a project with some 3/4" melamine and one side lined up perfectly flush yet the other side was off. when i say "off", im not talking about much (less than 1mm), yet it was still enough to discourage me a bit. this project doesn't have to be perfect, as it's mostly function over form, but it's still bugging me to no end. granted, the cut i was making was a somewhat difficult one due to the fact that i was plunging the tool without much support. i feel like this is user error more than anything but i still wanted to post it up and see if you guys are getting better results than this of if this is what i should be expecting. i think it's actually a bit worse than it looks in the picture.

approximately .5-1mm off

photo1-25.jpg

dead on

photo2-36.jpg

Posted

With the Domino and biscuit joiners you have to be constantly focused on holding it dead flat while plunging the blade in. If you watch someone using the tool closely there is a tendency to rock or wiggle as the plunge changes the leverage on your grip.

I take a steady stance and focus on feeling the fence being dead flat and maintain that straight line all the way in and out of each plunge cut. I clamp my parts with those Bessey auto adjust toggle clamps so they stay still while I am cutting the mortices.

Practice on scrap! Having someone watch you might help pinpoint when you are letting the fence tip up or down.

Posted

==> If you watch someone using the tool closely there is a tendency to rock or wiggle as the plunge changes the leverage on your grip...

+1 -- this is the challenge.

Posted
. I clamp my parts with those Bessey auto adjust toggle clamps so they stay still while I am cutting the mortices.

Practice on scrap! Having someone watch you might help pinpoint when you are letting the fence tip up or down.

Good idea on using those clamps to hold everything still . I'm a new domino owner so I can't add much other then I've had both perfect and no so perfect results using it . I blame myself for the no so good results , by doing one of or both of the above mentioned causes to poor lineup .

I have noticed that if I plunge the tool by holding the end of the machine I get a smoother plunge resulting in less movement of both the wood and tool . I think with any tool the more you use it the more comfortable you become with it . Good luck

Regards

Jerry

Posted

I have seen plants for a jig for biscuit or domino machines where you clamp the machine to a table and there is a fence around the face of the machine. Then you can set clamps and stops to hold small, narrow or angled parts in place and cut the mortice.

I printed out the plans , just haven't had a strong enough need to build it yet.

Wood magazine or Shop Notes not sure where I found it.

Posted

I know it probably wasn't your error in this case, but an error I came across a couple times was using the incorrect reference face.

I do not have a domino, but rather a biscuit jointer (same preface, basically). I was setting up to join a few boards together for a raised panel. I thought I had the biscuit blade set directly in the center, but I was wrong. Say I have three boards to join, side A is up and side B is down. I cut 2 of 3 slots with side A up, and the last with side B up. When I went to put the panel together, it was off by about 3/32 of an inch on both sides. I didn't realize what I did wrong at first, but now I am aware of my mistake.

I could have prevented it, but never really using the biscuit jointer before didn't help :)

Trial and error is the best way to learn!

Posted

Only tricky part about getting it dead-flush with Melamine is that it's so slick. You should be able to easily get joints flush; you'll be able to feel the joint, but can eliminate it with a block of sand paper. Practice a bit.

And what pghmyn said is dead on: most important thing to using the Domino is minding your reference surfaces. On the joint you have in the first picture, take the one that's vertical in the picture and spin it around (so face to left is to right and vice versa) and see how it aligns.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 57 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined