Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Help troubleshooting sprayed oil-based enamel issues

Featured Replies

I am building a bed that is a gift for a friend of ours. Her room decor is red/black so we decided to build out of pine and then paint it gloss black. I am using an Earlex 5500 and after talking to the guys at the local Sherwin Williams and explaining my project they recommend one of their oil-based enamels. I messed up initially by not priming, so the first coat ended up becomming $21 a quart primer (ouch!). After the second coat, the faces look like this but the end-grain looks good. I thinned the enamel about 5% and am using a 2.0mm tip to spray.

Any ideas as to what may be going wrong or what I can change?

Thanks in advance!

post-207-0-49196700-1354405496_thumb.jpg

post-207-0-58011100-1354405635_thumb.jpg

Sand between coats to level the surface. Haven't sprayed oil base in years but we used to add Penetrol to improve flow out. Got to keep the tip clean. Try cutting back on the liquid volume to improve atomization . Thin coats is always better, maybe you can increase it for a full wet final coat.

Part of you problem may be that the Earlex 5500 doesn't have sufficient power to atomize that type of finish to give you a good final product. I would suggest using a SW CAB acrylic black lacquer. That is a much thinner finish and flows out quite well. As for priming SW makes a Vinyl surfacer that is white and works very well and sands great. Sorry that none of those things are very helpful.

  • Author

Part of you problem may be that the Earlex 5500 doesn't have sufficient power to atomize that type of finish to give you a good final product. I would suggest using a SW CAB acrylic black lacquer. That is a much thinner finish and flows out quite well. As for priming SW makes a Vinyl surfacer that is white and works very well and sands great. Sorry that none of those things are very helpful.

That is what I was afraid might have happened. I was hoping that by giving the SW guys as much info as possible and voicing this as a concern that they could point me in the right direction. Do you think that i could sand what I have on now to smooth it out and spray the lacquer over that?

Depending on the viscosity of the material, a 2mm tip is generally too large for finish work. There are ways to cheat it a bit (increasing air pressure and cutting back on the material flow and increasing the spray pattern to get better atomization). More often times than not the specs for the particular finish will have recommendations for the various application. For example spay should give a % of thinner to add, air pressure and tip size for best results.

If I am guessing correctly on the paint you used (sherwin williams oil bsed enamel gloss) they recommended tip size of roughly .5mm and thin 5% (much smaller tip than what was used)

If you're looking for a very smooth finish, you'll need to let the material cure a few days (possible a week or more) sand it flush with some 600 grit and re-spray the topcoat with a proper tip size... Like what was mentioned thin coats are a big part of the equation. Don't expect to get full coverage on one application. Typically it takes 2-3 coats.

Hope this helps!

That is what I was afraid might have happened. I was hoping that by giving the SW guys as much info as possible and voicing this as a concern that they could point me in the right direction. Do you think that i could sand what I have on now to smooth it out and spray the lacquer over that?

The easiest option would be to sand the finish smooth and then apply the same stuff over the top with a foam roller you will get minimal stippling from the roller and sanding between coats will also help create a good final product. If you wanted to spray lacquer over the top would would most likely have to prime or surface the enamel. Good luck

  • Author

If I am guessing correctly on the paint you used (sherwin williams oil bsed enamel gloss) they recommended tip size of roughly .5mm and thin 5% (much smaller tip than what was used)

Yup, thats exactly what i used. From what I can see...the smallest tip available for the 5500 is a 1.0mm....I do have the 1.5mm tip but it doesn't sound like that will be small enough. I may have to just roll it on and chalk this up as a learning experience.

  • Author

Well I've worked my way back as far as 320 sanding and I've still got texture issues. I painted a small section and it looks like a hammered finish at this point. Not a horrible thing, assuming you want that look...which I don't. I am about at the point to take the RO to it and strip the paint off and start over with lacquer. I am less than thrilled with my local SW at this point. There is a place across the river that carries ML Campbell, so I may go have a chat with them...hopefully with better results.

I use ML Campbell Agualente. They have clear and tintable solid color ( paint) base. there is also sanding sealer. Works great with my HVLP turbine.

It looks like you're just not getting atomization. It could be one(or more) of several things: paint too thick, nozzle too large, too much fluid or holding the gun too close to the work. Did you check viscosity with the cup that comes with the Earlex?

I'd suggest trying the 1.5 tip, thinning about 10% and maybe use some Penetrol. Cut way back on the fluid and creep up on it until you get a decent coat. Keep the gun about 6-8" from the work. Practice your setup on some scrap ply, fiddle around until you get a good coat.

Attaching a generic chart for tip sizes by viscosity, it ain't the Bible but it's somewhere to start. Use the "Pressure Feed" column for the Earlex.

I've sprayed water-based acrylic enamel with the 2.0 tip on my 5000 and it has a good bit less power than the 5500.

You should be able to make it work, just take some time and experiment.

HTH,

Bill

post-1150-0-07253200-1355426188_thumb.jp

  • Author

So I found out today that you have to be a 'professional' to purchase ML Campbell products...ie, a business license or a Fed. ID number, so that pretty much nixes that idea. I did manage to find out in part where I went wrong with SW. I didn't realize that their 'paint' stores don't carry the full line of their products, if you want lacquers you have to find a 'finishes' dealer. I was close by so I went there and told the guy what i was looking for and he brought out some of their Opex Lacquer.

Now that i get the stuff home and look at the product data sheet it seems like this stuff is intended to finish metal, tho there is a mention of interior wood applications. Before I open this stuff up anyone have any opinions on if its suitable or not?

Opex Lacquer is perfectly fine for wood. I actually am spraying that same product right now. What product number do you have? (ex. M60 B 17) You can thin it up to 100% which is what I normally do and apply several coats you will be fine at 50% depending on your equipment. What did they give you to prime the surface?

  • Author

The product number is M61 B21. I asked about a primer and the guy told me I could build the finish up and still get a good finish without priming.

OK did you strip the project to bare wood? If not I would test it before you spray the whole thing. You can always use an oil based kilz primer and that should give you good adhesion. It is just important to test before applying because the lacquers can been finicky. However if you have bare wood I would even then recommend using some type of surfacer the suggested surfacer is Opex p61 or Sher-wood P65 W1. Hope this helps...

D is right. Test it first because often times, lacquer will reactivate the finish below it because of the solvents used. I've seen lacquer sprayed over enamel create some nasty finishes.

  • Author

I really appreciate all the advice in the thread so far...you guys are great.

I'm working on stripping the enamel off now and getting it down to bare wood and getting it back to finish ready. I should have that done tomorrow and will be able to test.

Hope the stripping project is going well Don... I know it can be a pain...

  • Author

Almost done, all that is left is the back of the headboard. Yesterday was a wash, went do dinner and a movie with the wife instead. I've had to stop for tonight, we are getting a band of thunderstorms about to hit and I was doing all my work outside because of all the dust.

  • Author

Test board... 6 coats of lacquer thinned ~50%. Smooth as glass and looks great. Now I just need to figure out how to set up my shop so I can spray the rest of the pieces inside where I can control the temp and make the dry times reasonable. If i haven't said it already...y'all are awesome. Only thing I love more than the folks on the forum right now is my respirator....man lacquer is strong stuff!!!

post-207-0-61502000-1356391401_thumb.jpg

looks great! I'm glad there lacquer worked for you. the stuff sinks bad though. keep a fan on it and you'll be ok. it dries really fast and has no recoat time so you can put 5 co acts on in a matter of min.

  • Author

I put 3 coats on the non-visible faces last night and went thru 2 pots of lacquer...so I am going to prime the outside faces and then lacquer them. Better to use some $18/gal primer instead of multiple coats of $50+/gal. lacquer.

  • Author

Snatching defeat from the jaws of victory...that's what I'm gonna name this bed.

Primer backfired. I rolled it on, let it dry overnight. Sanded it back to smooth the surface and get rid of the stippling i was seeing and feeling. Shot the first coat of lacquer, coverage seemed much better than going on bare wood (which is good) little bit of texture showing thru, but thought that i could build the finish up a bit. Wrong answer. After 3 coats of lacquer I'm back to basically a hammered look. Better than with the enamel, but still not what I want. Every single little bit of texture that I can't see when it was primed is now showing up under the lacquer. I've got about enough lacquer left in this gallon for maybe 2 full pots, depending on how much its thinned....

I just wanna bang my head against a wall at this point

Don, the problem may be with the oil based primer. I always use lacqer based sanding sealer under lacquer because the solvent in the lacquer could cause the oil based to reactivate and bubble. Paint a sample board with your primer and when is is dried, wipe it down with a cloth and lacquer thinner. See if the finish is effected at all.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.