dodgeram99 Posted December 12, 2012 Report Posted December 12, 2012 I have some really bad rust stains on my table saw top. All the rust is off. How can I remove these stains? I have used a ros with 800-4000 grit sand paper with wd-40. And several other idea. But none seem to remove the stains. Quote
rodger. Posted December 12, 2012 Report Posted December 12, 2012 I have tried (with no success) to remove some stains from my TS top. Now I call it "patina". As long as there is no rust or pitting, you should be okay. I know you probably want the "showroom shine" (as I do), but it's best to let it go. Over time, the stain is less noticeable. I had a coffee ring stain on my TS top and it drove me INSANE. Nothing I tried got rid of it. Over time it faded on its own and is now gone. Quote
Trip Posted December 12, 2012 Report Posted December 12, 2012 i would not try... most folks do more damage than good. as long as the rust is off and the top is sealed, then you should be OK -- just a little dirty... don't think of them as stains, but battle scars... Quote
Dave's Not Here Posted December 12, 2012 Report Posted December 12, 2012 A medium Sandflex block works for me on small area stains. Quote
CessnaPilotBarry Posted December 12, 2012 Report Posted December 12, 2012 Try a "Top Saver" family product called "Rust Free", followed by wax, Top Saver, or TopCote. It's excellent stuff. My local Woodcraft sells it. Shannon Rogers did a video podcast using this product to remove spots from hand planes. He's a member here. Ping him, and maybe he can provide a link to the episode. Quote
Alan Bienlein Posted December 12, 2012 Report Posted December 12, 2012 Here is a link to a method of cleaning your cast iron top. http://www.newwoodworker.com/clncstirn.html Quote
estesbubba Posted December 13, 2012 Report Posted December 13, 2012 FWW did a cast iron torture test and wax does very little to prevent rust in it. Even the popular one like T9 and Topsaver didn't fare that well. The winner was CRC 3-36. Think you need a FFW.com membership to view. http://www.finewoodworking.com/membership/fwnpdf/011227030.pdf Now I use Boeshield T9 and wax and wax and generally it works well but usually get surface rust in summer. Quote
CessnaPilotBarry Posted December 13, 2012 Report Posted December 13, 2012 FWW did a cast iron torture test and wax does very little to prevent rust in it. Even the popular one like T9 and Topsaver didn't fare that well. The winner was CRC 3-36. Think you need a FFW.com membership to view. I saw that, but it doesn't match my own experience, having tried most of the products, including 3-36. My only guess is that certain products work better in specific climates and situations. In my personal experience, some of the products might be better if you leave your table saw out in the rain, or in a storage locker, or a shop with wide temperature swings. In my relatively constant temperature shop, many of the products have other factors that push them down my list as a protectant on a surface that gets used on a daily basis, with tools and wood sliding around. The only reason I think in-use vs. in-storage has something to do with it, is that I live about 30 miles from the site of the test, and grew up in the town where the test was held, so I'm pretty confident with my assumptions about the test climate. ;^) For example, WD-40 did relatively well under the conditions in the FWW torture article. At our bicycle shop, we replace rusty chains on a daily basis for customers who use WD-40 as a chain lube. Quote
Trip Posted December 13, 2012 Report Posted December 13, 2012 ==> I saw that, but it doesn't match my own experience +1 I got some CRC-SP-400 from a marine supply house. It's messy, but protects like nothing else i've used. Quote
Beechwood Chip Posted December 13, 2012 Report Posted December 13, 2012 I got some CRC-SP-400 from a marine supply house. It's messy, but protects like nothing else i've used. Sounds like Cosmoline Quote
estesbubba Posted December 14, 2012 Report Posted December 14, 2012 My experience with Boeshield T9 and wax has been just fine during woodworking season. My tables will usually have some light surface rust after the summer, but WD-40, scotchbrite pad, and cheap finish sander makes quick work of it. I agree that a controlled environment makes a difference. If you're throwing your tools in storage in Florida then that's a different story. Quote
Trip Posted December 14, 2012 Report Posted December 14, 2012 ==> Sounds like Cosmoline not quite that tough, but think a really light / spray cosmol. greasy, but does 'buff-down'... Quote
BuilderBill Posted December 16, 2012 Report Posted December 16, 2012 Boeshield's Rust Free works well but it's pretty stout stuff. I used it to get a water ring off my bandsaw table but had to go over the whole thing with Scotch-Brite and a RO sander to get the finish uniform afterwards. Read the instructions! HTH, Bill Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.