Dave F Posted December 30, 2012 Report Posted December 30, 2012 I was this ==>II<== close to packing one in the back of my car and bringing it home today..... Had the Visa card out and everything..... Maybe tomorrow.. Quote
knotscott Posted December 30, 2012 Report Posted December 30, 2012 Grab a 20% Harbor Freight coupon, and try again! 1 Quote
Dave's Not Here Posted December 30, 2012 Report Posted December 30, 2012 He who hesitates is lost and also doesn't have a new table saw. 1 Quote
Pwalter5110 Posted December 30, 2012 Report Posted December 30, 2012 Dave, I actually have one and really like it. I am debating on wiring it up to 220V but I'm not 100% sure how much I will gain doing that. But all things considered it has worked well for me. 1 Quote
TRBaker Posted December 30, 2012 Report Posted December 30, 2012 Pat, if your saw is like most, you will see a world of difference between 220 and 110. I'll never run my saw on 110 again. Quote
knotscott Posted December 30, 2012 Report Posted December 30, 2012 ...I am debating on wiring it up to 220V but I'm not 100% sure how much I will gain doing that. But all things considered it has worked well for me. If you've got 220v available, I'd definitely do it. There's minimal downside, and some potential gains in startup and recovery speed, which can make if feel more powerful. If you don't have 220v, it'd only be worth changing if your 110v circuit is inadequate or overloaded...the symptoms are dimming lights, sluggish starts, etc. Gains from 220v are not a certainty...it's highly dependent on the particular circuit, and the particular motor involved. In theory, there's supposedly no difference, but in reality, many 110v circuits aren't adequate and/or are overloaded, and tend to suffer more voltage loss. There might be a noticeable difference, there might not. 1 Quote
Tom Wheeler Posted December 31, 2012 Report Posted December 31, 2012 I got mine in october and have built numerous projects on it already with no problems, The first thing i got for it was a zero clearance insert and a incra miter gage. I run it on 110v with no problems, but have thought of changing to 220v also. 1 Quote
Lumbermeister Posted January 1, 2013 Report Posted January 1, 2013 Another option, should a 220V circuit be impractical for whatever reason, is to install a dedicated 20A circuit at 110 volts. There is no reason that a stand-alone circuit should be overloaded, and the 20A wiring/breaker will permit sufficient margin for any spikes in power draw that might occur on the r4512 (has worked well for me). Quote
chipmaster Posted January 1, 2013 Report Posted January 1, 2013 I'm using a dedicated 20A circuit and have no problems. Occasionally I've had to move the saw and plug into another 20A circuit which has caused the lights to dim slightly for half a second but after that initial 18A start up it runs fine. I love that saw! My pieces improved by leaps and bounds as soon as I got it. I set it up once and it has held steady for a year with no adjustments necessary..Love that saw! You guys have made me wonder now about converting to 220..but some seem to feel there is little benefit, others say huge difference...eenie meeny myni mo...what to do. Is this where "If it ain't broke don't fix it" comes in? Quote
TRBaker Posted January 2, 2013 Report Posted January 2, 2013 My experience is limited to Delta, Powermatic, and Grizzly. I've never used a Rigid saw before, so don't go by what I say as gospel. Quote
knotscott Posted January 4, 2013 Report Posted January 4, 2013 I'm using a dedicated 20A circuit and have no problems. Occasionally I've had to move the saw and plug into another 20A circuit which has caused the lights to dim slightly for half a second but after that initial 18A start up it runs fine. I love that saw! My pieces improved by leaps and bounds as soon as I got it. I set it up once and it has held steady for a year with no adjustments necessary..Love that saw! You guys have made me wonder now about converting to 220..but some seem to feel there is little benefit, others say huge difference...eenie meeny myni mo...what to do. Is this where "If it ain't broke don't fix it" comes in? Every scenario is unique to the particular circuit involved and the motor's interaction with it. I've switched two of my saws from 110v to 220v, and noticed an improvement in start up speed and recovery speed in both, but one was more dramatic than the other. It's fairly common to find an inadequate 110v line, in which case a better 110v line or a 220v line would be an improvement. 220v tends to have less voltage loss, so if you're going to do some wiring, add the 220v line....there's little downside, and some potential gains, but no one is going to be able to predict the outcome for your circumstances. Quote
chipmaster Posted January 4, 2013 Report Posted January 4, 2013 Every scenario is unique to the particular circuit involved and the motor's interaction with it. I've switched two of my saws from 110v to 220v, and noticed an improvement in start up speed and recovery speed in both, but one was more dramatic than the other. It's fairly common to find an inadequate 110v line, in which case a better 110v line or a 220v line would be an improvement. 220v tends to have less voltage loss, so if you're going to do some wiring, add the 220v line....there's little downside, and some potential gains, but no one is going to be able to predict the outcome for your circumstances. Thanks Knotscott..I appreciate your insight. It really sounds like I should leave well enough alone since I'm really happy with my saws performance. Perhaps if I move beyond the hobby stage at some point, it might be good to look into it but I think I'm good for now. Thanks again. Quote
chipmaster Posted January 4, 2013 Report Posted January 4, 2013 I was this ==>II<== close to packing one in the back of my car and bringing it home today..... Had the Visa card out and everything..... Maybe tomorrow.. I have been looking to see if you ever got the saw and to say that I am very happy I got mine. I had looked at all the others..repeatedly..and couldn't pull the trigger until I really looked at the Ridgid and read up on it. No regrets here..great saw. 1 Quote
Dave F Posted January 5, 2013 Author Report Posted January 5, 2013 Thanks Chip.. Think I'm gonna wait till next payday.. so two weeks.. Quote
Byrdie Posted January 7, 2013 Report Posted January 7, 2013 I have this exact saw except packaged under the Mastercraft brand name and sold through Menard's. I didn't bother reading reviews or shopping. I had a certain amount of money to spend, was looking for some specific characteristics (mobile) and had a limited range I was willing to travel to purchase. I couldn't be happier with my purchase. I've had it a little less than a year and it's made a huge difference in the quality of my woodworking. Careful set-up and attention to details made all the difference in the outcome and the quality of the manufacture is excellent. After I purchased it I read some reviews that knocked the unit for problems with poorly machined trunnions interestingly enough all written by people who didn't actually have the saw. Mine run straight and true. With the aid of a Wixey digital angle gauge I get consistent and repeatable angles. Quote
Dave F Posted January 7, 2013 Author Report Posted January 7, 2013 Thanks for the comment Byrdie, glad it's working so well for you. Nice to know that you've got a quality unit. Good tip on the digi angle gauge too. Quote
Dave F Posted January 9, 2013 Author Report Posted January 9, 2013 HEY !!!! What's this?? It just showed up in my garage..... Quote
Pwalter5110 Posted January 9, 2013 Report Posted January 9, 2013 Thanks everyone for the advice on the 220V. Dave you will really like that saw. Quote
Dave F Posted January 9, 2013 Author Report Posted January 9, 2013 Thanks Pat. I'm looking forward to getting it put together tomorrow. Quote
Dave F Posted January 9, 2013 Author Report Posted January 9, 2013 Just so everyone knows.. These have been selling at Home Depot for $499.00 for as long as I can recall. I looked at Home Depot online earlier this afternoon and saw that they were now listed at $529.00. I ran by my local HD tonight and they still honored the $499.00 price. If you thinking about one, I'd jump now before the price increase sticks.. Quote
robjeffking Posted January 9, 2013 Report Posted January 9, 2013 After you register it they should send you confirmation. I called them 3 weeks after I registered mine and double checked and made sure all my paperwork was on file and in the system for the LSA. The stock blade is junk replace it as soon as you can. Quote
Dave F Posted January 9, 2013 Author Report Posted January 9, 2013 No worries there. I picked up a 50 tooth Freud Diablo when I bought the saw. Quote
jmaichel Posted January 9, 2013 Report Posted January 9, 2013 Congrats on the new saw. I have been looking at that saw for some time too but just not totally sold on it yet. You get reviews on both sides of the spectrum and its hard to make a the right choice. I do know that it would not be my last saw and that should make it easier to pull the trigger but it doesn't. Anyway good luck and more pics. 1 Quote
Dave F Posted January 10, 2013 Author Report Posted January 10, 2013 Well, she's on her feet and rolling around just fine. Build is about 70% done (the hard parts are over anyway). I'll try to finish it up tomorrow. Quote
Dave F Posted January 11, 2013 Author Report Posted January 11, 2013 There she is.... All gussied up and ready for the prom.... And with cuts that clean and accurate I may have to reconsider that jointer purchase..... (kidding, of course).. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.