Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Started to draw up my shop

Featured Replies

My shop is shaped like an "L" which I really like. The long portion is 10' x 20' and the small part of the "L" is about 8' x 10' (roughly). As of right now, that smaller part is going to still be used for storage for my fiance's family. However, I have free reign to use the larger portion!

 

I used Grizzly's shop organizer to put something together quickly about how I want the shop to be set up. Here is what I came up with:

Screenshot2013-01-27at44614PM_zps14fbb47

 

You can notice there is no assembly table, yet. But I was thinking that could go behind the table saw. Or, Something up against a wall. The table saw is the G0715P Hybrid saw from Grizzly, and the jointer is the G0656P 8" model from Grizzly as well. My grandfather left behind a floor standing drill press, along with a band saw. The large rectangle at the top of the picture is where I hope to put some tool, fastener, bit, etc storage. Something for my Festools, too.

 

The room is almost cleaned out. Just need to rip down the old drop down ceiling tiles and frame, and install new fluorescent lighting.

 

Also, I am very lucky about my 220v tool situation on this. They had a hot tub which they got rid of, and there is a remaining 220v line running through my room that exits to the outside right above my jointer. There is a existing junction box on the ceiling, so it should be easy enough for me to buy a little bit of 10AWG wire, and install an outlet.

 

My question about that is, can I put more than one 220v outlet on that circuit? Is it wired just like a normal 110v outlet would be in that sense? As long as I do not run both my table saw and jointer in tandem.

  is this your first shop?

 

don't forget that the tools not only take up floor space but they take up space around them for example the table saw needs room for lumber behind, in front, and on either side of that why it usually in the middle of the room.  you might want to plan for a finishing area something that you can set up quickly for example a curtain to close off one end of the room perhaps where your cabinet/ chemicals will be stored on a counter.  also after you figure out your tools start installing dust collection easer now then when the room is full..  i like to take some chalk and write where your tools are going on the floor helps you get an idea of space.

  • Author

  is this your first shop?

 

dont forget that the tools not only take up floor space but they take up space around them for example the table saw needs room for lumber behind, infront, and on eather side fof that why it usualy in the middle of the room.  you might want to plan for a finishing area something that you can set up quickly for example a curtain to close off one end of the room perhaps where your cabinet/ chemicals will be stored on a counter.  also after you figure out your tools start installing dust collecion easer now then when the room is full..  i like to take some chauk and write where your tools are going on the floor helps you get an idea of space.

I like that chalk idea. I will be doing that for sure!

 

As for dust collection, I will eventually be investing in stand alone dust collector. I think I will put it in either the lower or upper left part of the picture shown. As for the finishing room, I did think about using that smaller portion of the room that is going to be used for storage for the time being. When I get everything moved out, that part would be fantastic for finishing.

 

The position of the table saw is tentative, as it will probably be outfitted with a mobile base. Just incase a situation comes where I need a few extra feet on one of the sides for a cut.

 

Any other suggestions? This is indeed my first shop (that I am designing from the ground up). I have a blank canvas once the room is clean.

put in extra plugs more then you will ever think you will need, 

 

try and use one tool to act for another for example a jointer in in line with your plainer then you can slid your board throught the planer across the bed of you jointer to save room.

 

  try and put like tools together for example table saw, jointer, planer are all use to square and resize your stock lumber. 

 

for dust collection i would get a 1 1/2 dust collection and then buy small cheap shop vacs like the set in back of car kind to clean up any loose dust. that way you can set it by the band saw and get the loose stuff on top or you might want to think about buying a central house vacuume system then you can clean up every square inch of you shop quickly. its pricy but i think its worth it because you can keep your shop spotless in just a few moments. 

 

dont forget air compressor with the piping built in pvc will work just as well as coper and it cost less.  then you can have a hose real right about your assembly table. 

 

to save room you can build flip top tool stands then you can put box planer on one side and spindle sander on the other. 

 

what kind of shop are you going to specialize in? cabinets, small crafts, carving, boat building, furniture artwork ect....?

  • Author

put in extra plugs more then you will ever think you will need, 

 

try and use one tool to act for another for example a jointer in in line with your plainer then you can slid your board throught the planer across the bed of you jointer to save room.

 

  try and put like tools together for example table saw, jointer, planer are all use to square and resize your stock lumber. 

 

for dust collection i would get a 1 1/2 dust collection and then buy small cheap shop vacs like the set in back of car kind to clean up any loose dust. that way you can set it by the band saw and get the loose stuff on top or you might want to think about buying a central house vacuume system then you can clean up every square inch of you shop quickly. its pricy but i think its worth it because you can keep your shop spotless in just a few moments. 

 

dont forget air compressor with the piping built in pvc will work just as well as coper and it cost less.  then you can have a hose real right about your assembly table. 

 

to save room you can build flip top tool stands then you can put box planer on one side and spindle sander on the other. 

 

what kind of shop are you going to specialize in? cabinets, small crafts, carving, boat building, furniture artwork ect....?

More of a hobby workshop, but "specialize" in cabinets and furniture type things. I really can't put into words what I will exactly do in this shop. All I can say is these tools will either pay for themselves with client projects, or my joy of using them. Either way, I will be happy.

 

Edit:

Lucky for me, the breaker box to the house is within like 10 feet from the room. So, if any lines need to be run for receptacles it will be minimal work.

well just saying might want to decide if you going to make large cabinets, small end table, keep sake boxes, boats ect.... then you can folcus on the tools you need now and buy everything else later.  for example boat builders need large bandsaw, wood steaming systems,  lots of clamps eather home made or store bought.

 

a cabinet maker will need a router and table saw more then band saw.

 

if you are wood turner you can get away with jointer, band saw, lathe

 

so you might want to put some thought in your personality and stuff you want to make.

  • Author

well just saying might want to decide if you going to make large cabinets, small end table, keep sake boxes, boats ect.... then you can folcus on the tools you need now and buy everything else later.  for example boat builders need large bandsaw, wood steaming systems,  lots of clamps eather home made or store bought.

 

a cabinet maker will need a router and table saw more then band saw.

 

if you are wood turner you can get away with jointer, band saw, lathe

 

so you might want to put some thought in your personality and stuff you want to make.

I do not plan on building boats, nor do I plan on turning in the near future.

 

I worked at my parent's house for the longest time (and I still do until I get my shop set up). I feel as though I would be a hybrid type woodworker in my eyes. I like to build furniture like tables, desks, shelves, etc. But I also like to build cabinet type projects. Depending on the situation/client.

 

I think I have a router or two that my grandfather had. I am really unsure of all the tools I have access to from my grandpa. I haven't been in his shop in the longest time, and since he passed I have yet to look through all he had.

first chance make a list then you build around what you got and what you need. 

 

a good router will do just about any job and as far as im concerned a router table is a must.

 

this is the tools i feel  is a must in all shops and most can be bought on craigslist

 

tablesaw, band saw, miter saw, drill press, grinder, jointer, planer, router. and dust collector dont skimp  when your 80 you will be glad you put the effort in now and with these tools you can build most anything  after that its basicly adding extras like

 

mortiser, lathe  (love that you should try it lots of fun and takes up next to no room), steam box,

  • Author

I have been paying more and more attention to dust collection, and I am very thankful for it. I see how much my grandfather's lungs deteriorated from constant dust inhalation, and I do not want that to happen to me.

 

I appreciate the help, and I look forward to the process of actually putting the shop together soon. Once I get this new credit card in the mail, I feel as though I will put in my order for the new tools! Exciting times for me.

good luck and have fun remember craigs list can be your friend in buying great tools cheap.

  • Author

good luck and have fun remember craigs list can be your friend in buying great tools cheap.

Absolutely!

Are you putting in a workbench as well as an assembly table? I think siting the assembly table behind the table saw may be a problem. You may find you have something in the process of being assembled on the table and then discover you also need to rip something long and may interfere with the assembly. Although it may be good as out-feed support.

 

Do you need to site the table saw in the centre of the shop or could the right hand side (when you face it) be against a wall? Turning the jointer around and siting it on the right hand side immediately adjacent to the table saw may be a solution dependant upon stock sizes you work with and walk thru room.

 

Mobile bases are the small shops best friend. You can pull machinery out as and when you need it then.

 

Best wishes with the shop build, the space will be a great place when finished,

  • Author

The right side of the room in the picture has a giant stone work fire place that spans about 2/3 of the length. I don't want to block it off, or put any tools in front of it.

I want to put an assembly table between the top of the picture and the table saw. Or something like that. Not sure yet. Can't wait to get to it.

I wish this semester of college was over already :)

If there is enough power for a hot tub its probably a 50a then you may want to just think about a sub panel. With my shop I used masking tape and laid out all my tools where I wanted them on the floor. The electrical was then wired for each tool, then the tools came in.

Don

  • Author

If there is enough power for a hot tub its probably a 50a then you may want to just think about a sub panel. With my shop I used masking tape and laid out all my tools where I wanted them on the floor. The electrical was then wired for each tool, then the tools came in.

Don

Close, it's a 40a breaker.

Just stick all the tools in your best guess location and start working. You'll figure out what doesn't work fairly quickly and can then adapt.

  • Author

When they got rid of the hot tub, I assumed to wiring would still be present. However, when I opened up the box to trace the wiring, the only thing left behind was the breaker. No big deal, I still have a breaker to start with.

 

This is a picture of the inside of the box:

https://www.dropbox.com/s/sbz1s54804xv1bb/Photo%20Jan%2030%2C%2011%2038%2005%20AM.jpg

 

This is a picture of the breaker removed from the box:

https://www.dropbox.com/s/mgn0rqtyembm415/Photo%20Jan%2030%2C%2011%2050%2016%20AM.jpg

 

I am prepared to run the small length of wire to where my shop is. However, the only question I have right now is how do I know which wire to put into which part of the breaker? I see on the breakers that there are black and red wires for the 220v breakers in the box currently. Is there a designated spot for each wire or are the two wires interchangeable in the locations?

 

Also, correct me if I am wrong in this, but this is what I understand needs to be done:

1) Determine location of 220v receptacles in the shop.

2) Use 10AWG wire from breaker to receptacle, along with conduit. (is conduit necessary for full run of wire?)

3) Run wire, attach to receptacle, attach to breaker, then plug breaker into box.

 

I don't think I need a sub panel, because I will only have these two 220v tools, which will never be run at the same time anyway. If I do add a third 220v tool, most likely it will be a quality dust collection system. And for that, I have no problem running another line.

 

Any advice is welcome and I appreciate any comments.

 

EDIT

Second question. If I want to have two outlets on this one line, what is the best way to do this? Is there a diagram available or an easy way to explain how I would accomplish this?

10 AWG is for 30 amps, 8 AWG for 40 amps, 6 AWG for 50 amps.  It doesn't matter which wire goes in which hole in the breaker for 220V.  If I were you I would just hire an electrician...it sounds like you don't really have enough knowledge to do this wiring and you might end up burning your house down...

  • Author

A little side note, that I was happy about. I'm still in the process of cleaning out the room in the basement, and I came across three floor standing air filter units. Two of them are identical, and look unused. I'm not sure if they work, as I haven't tested them yet. I also found another one that is new in the box. I'm really hoping that one works, at least.

 

I thought they would be a really great addition to the shop space seeing as there is no direct outside ventilation.

  • Author

I have been looking for ways to light my shop, and I think I have the right idea, but I am open to suggestions.

 

The shop space I am going to first "inhabit" is 20'x10' and about 6'6" tall (I haven't measured exactly, yet). I am thinking about using three fixtures (linked below) spaced out evenly. I know they are plug in operation, and I am going to have outlets installed for each of them in the ceiling. The outlets are going to be "half-switched" so one is always hot and the other is controlled by the light switch. I figured that would be a good idea incase I even needed a plug above me for some reason.

 

http://www.homedepot.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=10051&langId=-1&catalogId=10053&productId=203081577&R=203081577#.URRbPVo3lpE

i find myself plugging in my router and power carving tools above me often.  its nice to have the cord off your table then you don't have to fight it as much.

  • Author

i find myself plugging in my router and power carving tools above me often.  its nice to have the cord off your table then you don't have to fight it as much.

I'm thinking I might make the ceiling outlets fully switched instead of just half hot/half switched. I don't see me needing the above outlets to work when the lights are not on. I will also have about another 5 outlets on the wall next to me. I am going to go to home depot tomorrow and purchase the lights and get them installed so I can finally go on the room without having to carry around a work lamp.

I like to have a separate 15A circuit for lights.  That way, if a tool pops a circuit breaker, you aren't suddenly in the dark near a spinning blade or bit.  I think this is best practice for all rooms, but I'd think it would go double for a shop.

 

You can still do your overhead outlets, just hooking them to separate switched (15A) and un-switched (20A) circuits.    

  • Author

I like to have a separate 15A circuit for lights.  That way, if a tool pops a circuit breaker, you aren't suddenly in the dark near a spinning blade or bit.  I think this is best practice for all rooms, but I'd think it would go double for a shop.

 

You can still do your overhead outlets, just hooking them to separate switched (15A) and un-switched (20A) circuits.    

I should have mentioned that I planned that :)

 

I couldn't agree more with the logic. At my parent's house, everything in the shop is on one circuit. I was terrified when I was in the middle of a cut on the table saw and the the switch flipped because someone turned something on upstairs. The circuits in my parents house are weird, as they are all over the place. One circuit covers the whole shop, another room in the basement, a kitchen outlet, and two outlets in the second floor. Then the others are all mixed about.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.